The Jalopy Journal
Agree with the above. Also, you have a lockup converter that's good for about 200 RPM reduction if it's working. Sent from my moto z3 using The...
Wow. I'd like to have had $800 for every Dana rear I've built. Check with the local 4x4 guys. They use a lot of Dana rears. The spreader is nice,...
Great guy. Will be missed. Always took time to answer questions. He delighted in firing up most any bike you showed interest in. Sometimes he even...
I'm reworking (replacing) the rocker panels on my 32 3w. I am using Brookville rockers, and making the inner panels. Does anyone know why the...
Cleaned with acetone, didn't sand. Peeled off in sheets. Sent from my moto z3 using The H.A.M.B. mobile app
I made the mistake of using POR 15 on a new piece of unprepared cold rolled 18 gauge. Looked great, but peeled off in perfect sheets. I thought...
Hi Squirrel. I just saw this post. Let's see. Far away from home. Cold weather. Bad rear bearing. Sounds familiar. Back in 2017 my son and I were...
Check with Brookville Roadsters. I think they are actually less expensive. Sent from my moto z3 using The H.A.M.B. mobile app
Summer of '68, 13 years old, put a flathead V8 and transmission out of a '48 Ford pickup in a '48 Jeep pickup. Installed hanging pedals, hydraulic...
Back in the late 70's, our local parts store hosted a seminar by their ignition parts supplier. The parts rep went through a very detailed...
Thanks again, Squirrel, for contacting James on our behalf. It was 36 degrees in Amarillo this morning, but it was warm in James's shop. Thanks...
I have a new best friend in Amarillo. Thanks again Squirrel and James. Sent from my XT1254 using The H.A.M.B. mobile app
Morning would be ok!! Sent from my XT1254 using The H.A.M.B. mobile app
Thanks Squirrel Sent from my XT1254 using The H.A.M.B. mobile app
Anyone in or near Amarillo,TX that can help me out. I found bearings. Need tools to change bearing. Sent from my XT1254 using The H.A.M.B....
I'm in Amarillo with a failed carrier bearing. Headed to SEMA. Need use of shop tools to replace bearing. Sent from my XT1254 using The H.A.M.B....
258 Drag Strip in Jacksonville, NC, 1968 or '69, Sox & Martin, Little Red Wagon
I have used a slide hammer with the small screw. Have also used a screw and flat washer with a right angle pry bar. I like the idea of using a...
I cut axle and some transmission splines. What do you need?
I have seen the pinion yoke splines wear and slap back and forth rotationally on the pinion. Have seen the differential cross shaft wear almost...
Outstanding build. If you don't mind my asking, what are your intentions with the roof?
Unfortunately, the original floor and cross channels are long gone. When I found the car in 1969, it had been channeled over the frame by hacking...
Not in southern California, but if shipping to or from North Carolina is practical, I might be able to help out. What do you need?
Nice car. Saw it at SEMA last fall.
Thanks for the reply, Bruce. Sounds like it is an early V8 car? It is a 3 window, originally with a rumble seat. There is a six, it has a straight...
Anyone ever seen or heard of a 32 frame with (star)174***(star) stamped in the normal places?
They both look great to me! Wish mine was that close. Flop, give me a call when you can. I can't seem to get through. I need to send something to...
Happy to see you working on this one again. Outstanding!!! I would love to have a set of the filler strips for the door top and cab.....to go with...
Hi Tom, roadster looks great, as does all your work. I know you are busy, but when you get back from Hershey, please give me a call. My email must...
My first drivable car was a 67 SS 350 Camaro. When I got it in 1970, it had the vented cap in the oil filler tube in the front of the intake, and...
Separate names with a comma.