The Jalopy Journal
Guys I'm happy to say after 2 months of fighting this.... Saturday I changed out the coil, condensor and points (all of which were less than 3...
So I have been fighting a hesitation for a month now. In the last month i have rebuilt the carb, installed a vacuum guage( runs 18hg at idle),...
If the chain jumped a tooth or two would the distributor match the piston tdc? I am also thinking about removing the flywheel cover to see if...
The truck was parked in 68. There are 64,000 mile on it but this is not the original engine. It is stamped as a 48 dodge 230 and had a paper...
Installed the rebuilt starter tonight , installed a fully charged battery and no luck. Still cranked very slow with the plugs in. Next I...
Yep it looks good. Sent from my SM-G920V using The H.A.M.B. mobile app
Here is what I've got going on. Last week I replaced the gas tank on my truck, while I was at it I fixed a issue of a air/vacuum leak at the base...
I have a issue with the stock tank on my truck, so I am currently using a plastic can and hose untill I can afford to replace it. What I dislike...
[IMG] Sent from my SM-G920V using The H.A.M.B. mobile app
[IMG][IMG][IMG] [IMG] Just a few of the times we used one of them.. Sent from my SM-G920V using The H.A.M.B. mobile app
Guys I had every intention of painting my 1940 plymouth truck, but as I drive it more the current finish is growing on me. I have used Polishing...
Moose, if I could bother you one more time. The misses wonders what it would be like with more teal? Like this color. [IMG] Sent from my...
He also rechromed everything for me.... The state of the fenders is one of the reason I am leaning towards suede paint. I don't think they can...
That looks fantastic. Thank you so much. Sent from my SM-G920V using H.A.M.B. mobile app
Does anyone have a example of a satin washington blue truck? I like the color, but wondering how it would look flattened? This is possibly going...
I am wondering if any one has any experience they can pass off about using a HAMB worthy truck as a shop truck and what deductions can be taken?...
Rick did a fantastic job hauling my two cars from georgia to VA. He was a pleasure to deal with and I would reccomend him to anyone. it was nice...
it only goes to zero when i floor it. most time it drops to 10 or so...
After the last situation of a vacuum leak and poor MPG I decided to install a vacuum guage. Here is what I have found: 62/ impala 327/300...
Your the second person to tell me .85. Did they offer different o/d gear ratio's. The seller says all saginaw od's were .75. Is there any way...
I currently have the m21 and have found a saginaw 4 with the overdrive installed, I am wondering if the switch is worth it. And what all will be...
What all is required for this switch. Does any one know if it is a direct bolt in other than reqiring a new shifter? Or does the drive shaft need...
Well here's the back story. I had a small vacuum leak which caused me to run rich. After fixing the leak I thought I should check to make sure...
Well I did some investigating. I guess I had a small pin hole in the line from the carb to the distributor.I measured a vacuum of 21 at the carb...
I tested the compression on the 327 this morning and found i have 100-105 psi on all cylinders. What would cause this condition? I have seen...
I keep a log of everything that I do to the car, and I have noticed that the intown gas mileage has dropped from a constant 14 mph to 8 mph for...
I'll second that. Mine caught fire due to a similar situation in october. Check your hoses.
Better watch out you got too much punctuation. The watchers will get you.
No offense was taken by anything said. I have recived so much information from this place...
Separate names with a comma.