The Jalopy Journal
It has been a long time since I worked on a dynaflow, but I don't think you would have to pull it to replace the parking pawl components. Here is...
I would put a piece of flat stock across your bell housing and measure to your converter pads record that information then remove your torque...
I have installed a fair amount of TransGo shift kits and probably 20 are more in 400's over the years. I have not installed a shift kit in about...
In regard to Blowby post # 2 here is a pen type digital multimeter...
I sealed my HF cabinet with white silicone bathroom calk when I assembled it. I also use a 2 1/2 hose going to my shop vac and installed a pipe...
Early 700's used 27 spline shafts the same as the 200-c and 2004r, the later ones used 30 spline shafts like the 350c but the converter hub...
It is not uncommon to use washers to obtain the proper clearence between the transmission and engine you should have a minimum of .060" not more...
Is there a whining noise that is coming from the bell housing area? What year 700 is this? 700r4 and 200-4r's would break the pump rings very...
Is there a tag on your 6 volt motor giving the amperage draw ? If your 6 volt motor draws 5 amps at 6 volts it would draw about 2.5 Amps at 12...
You should be able to test the lock-up by driving with two feet. When you are at highway speed lightly touch the brake pedal with your left foot...
I think all the aftermarket ones are made by Bob Drake! The last couple of years he has had them on sale for around $ 200.00. The last sale ended...
On the pictures you took of the Pan bottom right is a bump out to bled off the 2/4 band; There is a hole In the pan rail above that, I would bet...
Sorry in not getting back to you sooner; been busy the last couple of days getting ready for winter. If you look at the 700 valve body.gif...
Many 700R4 have stacked shifts, adjusting the throttle cable would be the first step, attached is a procedure put together by TCI. If you can not...
As d2 willys indicated the transmission is full when running when the level is at the pan rail; so if need be you could drop the pan and check...
The transmission mount sits back further than the th350; the 350 had 6",9" or 12" extension housings if your 350 has a 9" extension you may not...
Here is a guide from online metals http://www.onlinemetals.com/stainlessguide.cfmIn In my opinion you would want 303 or 416; 303 will be...
I would recommend a weatherpack connector there currently are 675 listings on ebay here is a 22 cavity connector...
I am going to start with the no engine braking in first; Was the rear band apply piston rings replaced and if so with what, I prefer the cast iron...
According to ATSG (Automatic transmission service group)the optimum temperature of transmission fluid is 175° for every 10° rise in temperature it...
There are only two pressure taps on a 350 mainline pressure and 1/2 accumulator pressure; If you install a pressure gauge at idle in drive you...
The transmission should hold 11 to 12 quarts unless you have a high stall converter then it would be less. If you cut some vacuum hose two...
Speedway has them listed 3.4" from stud center line to end http://www.speedwaymotors.com/Mustang-II-Outer-Tie-Rod-End,2105.html
The filter material in the original filter is a Dacron material that plugs pretty easily; when doing high performance transmissions I always...
The THM 250 were first used in Vegas; I am not sure what other platforms used them. I have never seen one stock behind a V8
That is the 1/2 accumulator it has a piston and a pretty stout spring between the piston and the cap; the spring probably broke and allowed the...
If you have a squeak or want to pre lubricate I would recommend Molykote® G-5881 It is made by Dow Corning it works great.
To reverse a starter motor you would have to reverse the current going through the field windings; since you are reversing both the field and the...
Little confused on the seal installation. This side goes into the hub first ( correct )
Seal goes in as is shown in the second picture; The first picture you show indicates the seal to be upside down, the lip would go towards the bearing.
Separate names with a comma.