The Jalopy Journal
FOR SALE are four 1932-50 Ford transmission/ clutch housing inspection covers that screw to the top of the transmission case below the VIN #. All...
This is a used Ford main drive gear, part # 81A-7017 in good used condition. 16 teeth, 8.25 in. long. Fits 1939-48 Ford Pass and 1939-50 truck....
This is a used Ford cluster gear # 68-7113-A in excellent condition. Tooth count is: 28-24-18-14. Total Length is 6.59 in. Fits 1936-48 Ford cars,...
This is a New Old Stock Ford cluster gear part # 022 7113-A. Tooth count: 29-24-18-14. Fits 1940-48 Ford passenger. 1940-47 light truck. 6.59 in....
This is Ford # 8M-7113 Cluster Gear in excellent used condition. Tooth count: 28-24-18-14 with 16 tooth gear. 1.125 in. bore for bearings. 6.59...
This is a used Ford 1939-48 transmission mainshaft in excellent condition. Helical and 6 straight splines. Has pin hole with 81A-7073 pin pressed...
This is a genuine OEM Ford special Belleview washer and bolt that fastens the U-Joint to transmission output shaft. No longer available like Ford...
This is the convertible top pump I removed from my Merc. It does not work. Aluminum top cover and related parts It is probably best for parts....
For Sale is one 8CM Mercury cast iron stock head. Driver side. Has never been cut, milled, sanded or surfaced. Sharp edges all around. No chips,...
Both have been SOLD. These are used Ford 1 3/8-10 transmission main shafts that can be used to align clutch disk, pressure plate with flywheel...
This includes a total of 6 wheel cylinders. Four are 1 x 1 1/8 in Right and Left for Rear Wheels. Two are 1 x 1/1/4 in., Right and Left for Front...
This is a New Old Stock Part # 01A-16138A bracket thatbolts to the front cross member and supports the two front inner fender aprons and fenders....
Today I went up into my attic and found the PETROBOND sand and related casting supplies I had ordered a few years ago . The sand is PETROBOND - a...
I have for sale my genuine OEM 1940 Ford rear wheel hub with genuine OEM Ford made wheel bearing. Bearing and hub are in perfect excellent...
Have for sale a pair Hemi 4 bolt exhaust manifolds that fit 331 -354 and 392 hemis. These came on Chrysler 300's. I had them ceramic coated grey...
For those who are running an 8BA Ford V8 or a 49-51 Merc engine with a 1949-51 Mercury rear sump oil pan and dip stick, here's the correct oil...
I saved this from my 51 Merc. It's used OEM but in good condition. 5/16 in. thick. Shipping is extra. It fits the set up shown here. NOS OEM Ford...
These are original magazine ads saved from old magazines. Very, very good condition. They look great framed and hanging on your wall. Postage and...
I have an old Holley 390, List 8000, 4160 Holley 4 barrel with a manual choke. However , part of the manual choke linkage is missing. I am trying...
A friend of mine in Daytona called me a few minutes ago and told me that this year's 2022 Turkey Rod Run will be the last one. Didn't know if...
If you buy this tool you need to print out the instructions below. I just bought a Inch Pound SanLaing Torque Screwdriver only to find that the...
I see where PERTRONIX I says that it's module should not be subjected to more than 8 AMPS. Would it be OK to install an 8 AMP fuse on the RED...
I made the mistake of hitting the starter button when the rotor was removed from my distributor that has the ML-181 Ignitor I set up installed....
I am hoping that a fellow HAMBER can help me as I called Pertronix today but couldn't get through and talk to a real person. Several years ago I...
I am considering installing these lights in my 40 Ford. Has any HAMBER used these lights? Feedback or suggestions appreciated. I would also like...
This came off my Merc so I know it works. Part# 8M-6915 Alternate part # A9AZ-7A651-A. Shipping is extra. Wiil be shipped First Class in a small...
Does anyone know what freon is compatible with the old R12 freon used in older vehicles? About 5 years ago I used a freon that was compatable but...
No, it's not the $1.9 million Merc.. I am talking about the Danbury Mint replica that a friend gave me years ago. When I first received it I...
It is my understanding that after Ed "Big Daddy" Roth passed away his son continued to honor his dad by selling signed posters and artifacts....
FOR SALE (This ad supercedes any previous ads.) Ten Rodders Journal posters at $5 each plus shipping. Each poster has a "front" and "back"...
Separate names with a comma.