The Jalopy Journal
If i can charge up a condenser and it holds a charge is it good? Or are there other things that can be bad, as in bad enough to toast points? I...
Edit, I'm and idiot, see post #43 I just fired up my shinny new 327 to break it in, and i'm pulling about 7lbs at 2000 rp, on my also untested...
Will the drive unit fit? I'm pretty sure gears interchange, minus the big/small circle stuff having to match up, but what about the actual drive...
On the input shaft bearing retainer, what is the thinner gasket that comes in the standard rebuild kit?? I just stripped out and had to helicoil...
I need a 19mm id bushing to repair a muncie tailshaft shifter bore. 19mm comes out to .748 and the shaft is .746, not perfect but close enough in...
I need a drum that dissipates heat a little better for my '65 el camino, I'll make anything fit as long as it is the right diameter and atleast 2...
On the tailshaft of the '66 muncie i'm rebuilding there is 2 spots in the middle of the reverse gear spline where it is counterbored with a clip...
So i'm building an L79ish(350hp) 327 for my daily '65 el camino(3200lbs or so). I have both a wide and close ratio muncie i can use, and i'm...
Edit, thanks guys, my math was off, I'd been working in the shop for quite a while after a long shift at work.... Checking my math vs a few...
Last time i bought some they had 70/30 and 80/20 at decent prices, right now they are 10% off with the code hot10 until the 10th of this month....
Anyone used these guys? They are STUPIDLY cheap on some kb 327 pistons i need for a build, i mean, i can get pistons and rings for the same price...
I just threw my full mech advance "rev-pol" mallory dual pt on my distributor machine, and i'm getting as follows 900- 0 deg 2000- 7 deg 3000- 11...
I finally found a parts store that could re-crossreference the points for small block chevy mallorys, they are Standard part number MY200 and i...
So on a 327, with a mallory YC(4 lobe black cap dual point), packard 440, and not running a ballast resistor, which is the right bosch coil? The...
Can i use the standard stamped plug that can be bought from holley(or summit,jegs, ect), over the emulsion tubes in place of the solid plugs that...
If given a choice which rods would you run with, 5.7" or 6" ??? I was just pricing out pistons and i realized that ones for 6"ers are pretty close...
I'm not even opposed to mixing up unsafe chemicals if anyone has any of the old industrial recipies, infact i'd prefer it(F' the EPA). I havent...
http://www.tapplastics.com/product/mold_making_materials/casting_products/tap_clear_lite_casting_resin/75 I'm looking at casting up my...
www.youtube.com/watch?v=GlCFBexBWGU A vintage 30 min movie on our favorite plastic type stuff
I'm talking the ones with the formed body instead of the older style like smitty's with the crimped ends. I tried to look it up in my old mags and...
http://www.jalopyjournal.com/forum/showthread.php?t=858788 How is this tradionally 'styled'? I posted in the traditional secton for a reason,...
So my current setup is gunna involve a mallory YC, standard brass mallory condenser , dual point, and packard 440 wires on a 327(it's in a '65...
I know they sold kits a bunch of years ago to weld bigger sumps on stock pans, but i just did a little hunting and didnt see any. Are they still...
I need a set of bushings for the reverse idler gear and my normal places dont stock them, and i cant seem to find them anywhere. I just contacted...
I have a gm pattern t10 with a 12/66 tailshaft date??? Hadnt they replaced the t10 by then? Also i assume this is an non-super, am i right?
I need a new motor for my daily(65 el camino), well not "need" but I want. I basically have almost all the makings for a L79 longblock, and I know...
I have a pile of gaskets that i'm looking to probably turn on here since my property taxes kinda raped me(long story) but i cant find the part...
I think I ordered up a radial tube for my model T but i'm running bias ply tires...
Separate names with a comma.