The Jalopy Journal
[ATTACH]15x7 3"offset Chevy bolt pattern..
on my 440 from the water pump fan mount to the edge of the crank pulley is 1 1/2'' from the w/p fam mount to the center of the crank pulley groove...
[ATTACH] a few more pieces to the puzzle...any thoughts/ideas welcome....
with this 413 or any engine for that matter.. what is the ideal if any on engine placement.. like forward, backwards, and hight of enging on...
iam looking for the best ideas in putting the floor in the 23 t... wood and glass or all glass.. all ideas or pics would be helpful... thanks.
Here is my new project....yes yes i know its a t buckt... its what i have to work with...:)i have a 413 carb to pan to trans, thats going in...
is it simple to add axles and backing plates from a doner 8 3/4 to a stock 65 rear end and get rid of the tapared axel set up...looks as if it...
anyone have a pic of the location of a stock vin number on a 49 mercury 2dr?
my stock fuel tube is in the trunk,had a cap with a hole in it to use as a vent... smells like gas inside the car....i found the stock cap witch...
[attach] [attach] [attach] [attach]
http://www.youtube.com/watch?v=YJLFAXVNv_Y
does anyony have a pic of the pieces that goto the wiper control that goes in the dash, i have the control, knob and the outer bezel, but looks...
iam looking for a detailed pic of the turn signal pieces under the steering wheel for a 49 merc
anyone know what a stock 49 merc fuel sending ohm reading is, need to match it with a 12 gauge
someone told me you can use a s10 wiper motor to convert the factory vac motor to used the wipers, any ideas as to the best diy way to make it...
here are a few pics of what i have been up to, i have a long way to go, but i like it... [ATTACH] [ATTACH] [ATTACH] [ATTACH]
I went on sat, WOW great show once again.. lets see som pics...
any tricks or tips on replacing a rear 3 pc glass on a 49 merc?
i need a pic of a stock 49 mercury hood hinges installed, i have a set that are apart cant figure out the way they go back togeather
i have a early model nova front clip that has power steering and a small block chevy with late model heads, what exhaust manifiolds and or headers...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]her a few cool pic i thought you might enjoy...
went over the front end to day, all looked good, swaped out the front tires, with a set of new ones, on loan from a friend, tried it out as soon...
this should be interesting.....its time to get to the bottom of the issue, when i do i want to see how many people guess right to the death wobble...
i have the master cylinder that has the pedals mount to it, that i want to rebuild, the kit i have for it, doent have all the parts that the stock...
is there a converson for a automatic for the flatty six besides a stock auto, car has manual in it now, needs auto, advice needed
thinking of scallops, with a matching top piece on my coupe, this is just an idea, need input.. [ATTACH]
[attach]its a 1940 all original businessman coupe rust free 48kmiles and is ready to go... [attach] [attach]
just thought i would give an update on my quest of the death wobble, i went form cowl steering to a 46 ford box mounted on the frame, to see if it...
i went from the cowl steering to this setup, thoughts about it wanted, [ATTACH] [ATTACH] [ATTACH] [ATTACH]
does a drag link, from a cowl setup, at a steep of an angle to the steering arm, cause a low speed wobble issue, i think it doesn't know the...
Separate names with a comma.