The Jalopy Journal
I have been a fan of Genes for years and ran across this articlehttps://www.alkydigger.net/category/racing-the-early-hemi-by-gene-adams.html
Has anyone built a 390 with using 352 rods and cut the tops of pistons enough to zero deck
Best horsepower potential Arden flathead or 241-270 Dodge hemi.
My neighbor kid went to a junior college trade school he is a whiz with a scan tool and as a parts changer . He ask me about a engine noise...
https://www.facebook.com/photo?fbid=1950554671946670&set=gm.1444875656280409&idorvanity=531263257641658
When replacing a timing belt on a roller cam 2.3 ford I was surprised how much easer it was to turn the cam than the old non roller cams Got me...
I like guys the build the unusual two of the best were Joe Penek and Rich Fox.
I'm a fan of Chris Nielson cams out of Farmington Ut did anyone take over after Chris death.
Does any one have figures on how much of the time say a SBC operates with the relief valve bypassing oil? The reason I ask is when building a 270...
Good video [MEDIA]
36 pontiac, 1939 Lasalle, 1937 Buick 1938 Packard Sorry about the care and not cars I dig the old Buick straight cars....
I saw a car on facebook that looked like a 1957-58 Ranchero with a box bird front clip the car was super rusty but cool. It got me to wondering...
Had a guy bring me his 63 Fairlane that had a vibration that he had swaped the 221 for a 289. Turns out he used the 221 balancer and flywheel. A...
If your in south central Kansas come to the Norwich street drags 4 30 22.
What would be minum wall thickness on a Ford 390 with a short fill street motor. I am thinking about building a 428 using a 390 block.
Saw this on Face book I think they are Model...
Interesting take on firing orders...
Even car manufactures goofed on this. back in the late 60s open chambers got to be a big deal less valve shrouding better breathing but we had...
Why is it that when you quit driving a car that you have to pull the aircleaner off?
Don Garlits turned 90 on the 14 th Happy birthday late.
Disk drum vs disk disk Alot of car started with a disk drum conversion and later went to 4 wheel disk. My question is does it stop that much...
I was given a set of SBC Harland Sharp rockers. The guy said he didn't like them Not enough oil getting to the top end after the change . Does...
Auction in Iola kshttps://www.sundgren.com/model-t-haven-liquidation-auction-in-iola-ks-cars-parts-tools-equipment/#jp-carousel-75132
Anybody going to Salina this week?
During a little bench racing stuff we did when running street car at the strip. One guy brought up running a switch to bypass the resister and...
Has anyone came up with a good needle seat tool? Screw drivers have a blade that is to narrow unless you get a monster that is 2 feet long.
I'm working on a Jeep 4 cylinder and I saw one intake valve stem a 1/4 inch higher than the others. I figure bad seat. Pull the head and that...
I tried to get a question answered about a part from Classic industries I waited and finally put the phone on speaker and laid the phone down 47...
http://www.midamericadragway.com/uploads/1/1/7/4/117420570/swap_meet_2021.pdf not a bad meet But Kansas largest out door I guess they have not...
May 8 Godard Ks ( Wichita) 73 cars 84 bikes http://users.neo.registeredsite.com/4/2/7/17398724/assets/Meyer_5-8_Sale_Bill.pdf
Separate names with a comma.