The Jalopy Journal
Need some advice, getting ready to install the hood on my '40 truck and can't decide if the hinges should be mounted on the cowl first and then...
Crossmember is straight, surface rust only--not all pitted. Has a couple of "hair-line" cracks around one of the U-clamp holes and another in the...
Pair of '39 DLX-'40 Ford hood supports. Were media blasted and primed. Sloppy pivot rivit was replaced with a shoulder bolt and brass washer....
This is the one year only hood brace/latch assembly for for '41 1/2 ton trucks. Media blasted and primed. Includes latch pieces as pictured....
Lime Works TS112 turn signal switch. New unit, was mocked up but never used. $100. SOLD. Optima red top battery mount tray--aluminum, used. $25....
Nice original '39 deck lid handle with license plate light & mounting bolts. Also, set of '39-'40 rear fender mounting clips. Light rust on some,...
Very nice pair of '32 running board support brackets. Been media blasted & primed. No twists, bends, not pitted junk. Will fit in a USPS small...
These are '39 DLX only safety latches for your hood. Ford made a production change mid year. These are both examples. Will fit in a USPS small...
'40 std. dash with glove box lid, ash trays. Media blasted & primed. Radio speaker grille hole has been made a little larger for some reason....
Very nice 59A style oil pan. Hot tanked, media blasted. No rot, few small dings. No stripped bolt holes. Includes NOS drain plug. Also...
Pair of loaded front backing plates. Nice parts from "Dry" North Dakota. Surface rust only--not pitted junk. Buyer pays shipping. Thank you. SOLD
New parts, only used in "mock-up". Standard 3/4" bushing spring perch. Dropped steering arms.
Wonder what others are using for jets & power valve in their dual 97 set ups? Edelbrock heads and speedway dual carb intake. MSD fired Mallory...
For sale, original '32 Ford clamp assembly. Top & bottom are original Ford, U bolts are modern replacements. Brackets were media blasted &...
Various Ford throttle linkage/spoon gas pedals. Two are '38-'40 and the "spoons" are Ford truck. Included are bits & pieces needed for install.
The stock seat springs in my '40 Ford truck are in pretty decent shape and I would like to reuse them and plan to buy the "cartouche" upholstery...
I read (probably on here) that the Ford F250 16" wheel has the correct size inside diameter 13-5/8" to accept the '40-'48 ford center. My...
'39 Ford deluxe closed car dash. Complete with what you see. It is weathered with surface rust. One stress crack has been welded. Straight and...
Pair of rear axles for '42-'48 Ford Banjo rear. Keyways and threads are excellent. Axles measure 33-11/16" inches. Shipped by FedEx ground.
Low deck Dodge parts. Usual wear on rocker tips, one set is stuck, other moves easily (they are not rusty) valve covers are very nice and hard to...
FS 94 carb. cores. Four are #91-99 ('39-'41) and one is M/N 59 (46-48) all have Ford script marked bodies. Units are complete as shown. Two of...
FS, pair of '40 front hubs. These were media blasted, primed and new Dorman studs installed. They have been machined on the back side to drop...
Pair of rear brake backing plates for the big bearing 9" housing. Plates were media blasted, primed and painted with semi-gloss chassis paint....
Several sets of hood trim for the '39 DeLuxe hood. Two front pieces, one latch handle, two center grille bars, four pieces of bottom hood trim....
Original Ford door latch assemblies. Includes both drivers and passengers latches. These will fit '37-'40 Ford closed cars. Solid condition, not...
OEM motor mounts for chevy V8. Genuine GM parts, not off shore junk. Includes correct mounting bolts. Bought years ago for a project--never...
I have a decent Waltham speedometer for my '40 pick-up but the odometer numbers are faded away. I have not had any luck finding vinyl number...
Have a NOS flathead oil pump that has gotten surface rusty after decades of sitting in a box. Would like to drop it in my mollasses tank to...
Set of 48 head studs for flathead Ford. Most are NOS genuine Ford. All studs are 3" in length, good for aftermarket heads. Price includes...
Brackets from a 1965 chevy 327" small block. Includes two power steering pump brackets and a double belt pulley (7-3/4") . Alternator brackets....
Separate names with a comma.