The Jalopy Journal
only cost 2400 to send a car from ny to england.....2700 to france
also, 4.56 posi rears do not allow easy manual pushing of your car....the rear tires will fight each other when the steering wheel is turned and...
i've used 55-64 rear ends in most all my hotrods since 1964 - yes, there have been many....i have never had a problem with the pig....i have had...
I have 2 of these exterior stainless drop down door handles and cannot remember what I took them off from...any ideas from the experts out there...
1935 ford flathead engine...rebuilt...bored .030 w/ aluminum flat top pistons...run very little....looks like new inside...stromberg 48...
i would like to see your build AS I am doing something similar....i am from upstate ny....i will contact you when i return home in april....johnnyB
doing one myself without the grille and front bumper...blown 392 hemi powered too....in the planning stage right now but the driveline is done and...
got tired of sending my $ down the drain when drag racing my 426 engines....went looking for the older version for my streetrod...first one was a...
found my first 392 hemi in a junkyard in northern pa....it was running, but not too good in the BACK of a ford econoline van.....had a 2"...
just picked up a 54 f100...thx for posting...this looks like an easy chop...no messing with the glass which few can cut without breaking several...
lowest in binghamton ny today at 2.69/gal....
could be...i took the pic earlier this year and did not write down what car it was from/in lots of kool rare stuff in this yard - maybe 50 or...
engine as found in a northern Pennsylvania yard....1000 vintage cars 1900's-1960's for the most....this chia was found lurking there in a vintage...
i will call hotheads at some point - maybe soon!....i guess i need more engineering befroe i build!....just trying to keep the cost down, but i...
....i understand the idea of running them down the hole a bit, but is this only accomplished by shorter rods or crank regrind?...am i missing...
HEY ABONE...WHAT ENGINE ARE YOU RUNNING?
my friend might have a set of steel fenders...i will check with him - if you still need them, let me know.....johnnyb
i've been collecting for a couple of years now AND AM ABOUT READY TO BUILD my 392 hemi...biggest porblem for me is $$$....i have heads with 3...
not to be too stupid, but how do I log off when done on the HAMB?
6th street in austin is a 'happening' - just to say you were there is big.....sometimes in the local parks, there are concerts...check with the...
old chevy monza's had a small diameter spare that expanded when filled with air...i think they were 14" chevy 5 lug as the monza had a v8 for...
great so far - where are you putting your alternator?....i ran a 392 in my A coupe and had to make a 'special' mount for the alt down low - looks...
NOTHING except the 'O' ring should be holding that dist in - pry it out!...you can always get another mallory...there is only a 4" 'stick' in the...
george is popular with all the girls - even at 86 !!!...he talked with my daughter and i got in about 2 words - truly a man with a 'young' eye -...
SCREW IT...THE RODS MUST GO - TOO MUCH ALREADY INVESTED - IT MAY PUSH MY DATE OFF A BIT, BUT THIS IS NOT WORTH THE CRAP I COULD GET IN THE END -...
i used a 1970's chevy truck hood piece and welded it over the opening - lots of filler to get it contoured right, but it came out great....cheap too.
these are all NOS - never used - it's a toss up......looking amybe to trade them to my friend with an old front engine hemi dragster for some...
absolutely a hobby car, but also a short drive car...we will see next year if it can keep together...i am doing this cause i have most all the...
OK, I GOT THE SKINNY ON THESE RODS STRAIGHT FROM BOB AT HOWARDS - THESE ARE NOS 'OLD' RODS - THAT IS, THEY ARE 2014 ALUMINUM AND ARE NOT SUBJECT...
yes, i already have them - got them with the pistons - probably from some guy that had the same scenerio as i have now - only trouble was, he also...
Separate names with a comma.