The Jalopy Journal
I have four chrome rims, 4.5 ford ..5 inch front and I believe 7 inch rear. They have towel city slicks with grooves on the rears and the fronts...
This is my all steel 33 Ford 3 window coupe, TCI chassis, 302, AOD , 9 inch May trade for 32 steel Vicky. A somewhat rusty old 32 five window hot...
Did any five window coupes come with duel wipers? Thx
Can someone please tell me what the crank shaft pulley should be to torqued to?
Does this look right I think I put the clutch fork in backwards which is causing the arm on the outside of the transmission to be in the wrong...
Just want to see what you guys are running for headers in your 1932 ford with an 8BA with a stock 32 steering box. Fenton, reds make your own ???...
I need some opinions from experience 1932 ford stock frame model a crossmember and spring ladder bar set up and I have 2 " of clearance with all...
I am about to install a new lower race into a 32 steering box and its a very very tight fit. Is this a heat the box freeze the bearing job?...
I know the 1932 steering box has a 13:1 steering ratio and the 33/34 has a 15:1 ratio can they be swapped fairly easily 34 guts into a 32 box?...
I need to know what this panel is called if anyone can help me out and it's purpose? I think its for a 1932 3 window.
I am going to be putting a 8BA in my original 1932 frame can anyone tell me where to weld in my motor mounts say the measurement from the center...
I have a 1980 rebuilt super t 10 that I would like to use behind my flathead is this possible if so what adapter do I use the only close kit I see...
Anyone tell me what year pedals these are? Thanks 27
How does this sound Super t10 Nodular Iron Case $250.00 but it pops out of third should I pass or grab it??? 27
Just need some help with my 32 3 window dash? I understand how the bottom of the dash goes in with the 4 bolts just a little lost on the top of...
The hub on the left has the grease seal installed and the grease seal on the right hub is just sitting on top and the seal is showing the...
Just want to ask how many leafs you guys are running in your coupes? I have a model a spring and just want to know if running 6 to 7 leafs is o.k?...
This may be stupid question but here goes I have a set of 1940 rear hubs I know the bearing go in first but whats next? snap ring then rear seal...
I have the chance to buy an early Halibrand Culver city quickchange that the seller says is magnesium. My question is how will I tell for sure...
I have the chance to buy a 1955 331 fully rebuilt this year with receipts for parts and machining for $5000.00 complete carb to pan and I can hear...
I am building a 1932 coupe and I have a qustion regarding the original k member. Do most of you remove and run a tubular/square style center...
I need some help with wheel and tire combo for a Deuce Highboy coupe. I have 4 black powder coated early ford wheels 2 -16X4" and 2-15x5" and...
I am about to buy a steel 32 3 window that is in primer and had all the body work done about 8 years ago my only concern is that on the surface of...
I have a 5 inch dropped axle 34 bones and 1940 dropped round back spindles and my tie rod still hits the bottom of my bones can I notch out my...
I have a 1931 roadster going on an original 32 frame with the stock k member and want to set the rear pinion angle? It has a 53 239 flattie and 39...
Does anyone know where to get the bolts to attach the backing plates to the banjo bells for a 40 rear axle or do I just use a 1/2 standard bolt?...
I have a 40 ford banjo with stock spring perches and an original model a spring will a set of pete & jakes shackles work or will I have to use...
I have a 1931 model a roadster on a original 32 chassis and am putting together the rear suspension and want to know if this sounds safe I have...
I have a 31 Ford roadster and using a stock 32 frame but am replacing the stock 32 crossmember with a model A crossmember do I put the model A...
I know this is been covered here before but I just wanted a little more feedback? 239 60 over winfeild cam 2x2 or 3x2?? 27
Separate names with a comma.