The Jalopy Journal
Since the body is sagging so bad I'm thinking it maybe better to square the cab on the shop floor instead of on the frame so it has more support....
Ok, thanks for the help I really appreciate it. I'll get my braces in on RT side and go from there. Thanks
Yea I know that I need to brace the heck out of it. I guess I just need to keep moving things around until I get both doors to fit. Since I have...
I'm working on a 48 Austin A40 pick up, It has rusted out cab mounts, rocker panel and lower hinge area on the A pillar. The RT door fits and...
The motor is a Lt. The end play is .006,I have pics and specs of every step of this build. Next we will try a Gm factory seal,I have had quite a...
no I didn't get a sleeve with felpro seal, is that a seperate part # becouse I havn't seen one with a sleeve.Or is another brand seal?
First thing its a brand new Gm engine, after the first seal went bad I bought the Gm seal install tool so I knew that it would go in straight and...
I do have 1 piece pan gasket.
I have replace rear seal twice using felpro # 40520 this last time I thought I wuold try a new housing also.Fired the motor and after a1/2 hr run...
I am working on interior and want to see pics of how headliner trim was done at the edges above the doors and around back windows on the Austin...
As the title says I am looking for pics and interior ideas for the Austin.I have looked in every megazine but they never show interiors.So looking...
Seb,Im not sure I understand what your saying,and how do I check the concentricty?What I think your telling me is that when the bearing retainer...
the first time it was the seal for sure,I don't know if it is the seal or secondary shaft cup should know tomorrow if I can get home from work...
I talked to them a month ago and let them know that they put the wrong seal in.They offered to send me the correct seal but I didn't want to wait...
I had Libertys Gears rebuild and face plate my gear box and it works really nice.The problem is the front bearing retainer seal they put in was...
I second the Honda, bond its good stuff
School me on down shifting my doug nash 4+1 that has been face plated.There has to be a way to down shift it,I just havn't figured it out yet and...
Where do you get the Brad Penn or joe gibs oil ?
I am going to make my O.T. 69 short chevy truck with a mild sbc a daily driver, and want to get rid of the POS 670 street avenger.So i am trying...
I did a search and didn't come up with any useful info.Does anyone have any real experience with the new 625 street demon. I have been thinking...
After pulling it apart and blowing all the passages out 3 times I got it to where it idles good and not so rich. the air/fuel screws aactually work.
This motor is a 69 bottom end with the vortec iron heads I have about 2500 miles on fresh build.Granted it has seen alot of garage time and not...
I have always used a vacuum guage for tuning.I pulled the power valve out it seemed to be fine,I couldn't suck air through it so I assume its...
no it wont die stumbles but wont die.
Floats are right at the bottom sight hole. I will check the air bleeds thanks.
I have had a few holleys and all have been good and trouble free. The street avengers are another story,both of them have nothing but problems...
I have been through their tech section and talked with them over the phone a couple times not much help.I had the 770 version on my chevy II had...
I have chevy with a mild 350 with vortec cast iron heads.I am running 10 initial and 30 total advance at 3000 rpm.It has a street avenger 670...
I made this one for my Austin it mounts backwards on the frame rail, in front of the engine using the small nipendenso alt.I didn't have room to...
Thanks Speedy thats what I needed.
Separate names with a comma.