The Jalopy Journal
1957 283 short block.No side mount cast on block.Numbers on block373148,D27,F403FE.$600 you pick up
32 spreader bar for rear tire mount.$100 +ship
2 Speedway Super 97's $250+ship 2 Holley 94's $175 +ship Both are rebuilt a few years ago.
2 vacuum canister for 40 Ford convertible to raise and lower top.$125 +shipping
2 flathead Ford transmission side shift for 40-46.$`25 each +ship or you pick up
1935 Chevrolet 2 dr sedan.Have lots of new parts.New SPW power windows and new glass and w/s and back glass seals.Corvette rearend.New Speedway...
Hobart Cyber-Tig 300 amp welder.Older unit but it works great.Getting too old to move it around.Also arc weld.Water cooled.industrial welder.Need...
On my 40 have a problem with fuel pressure.Last 2 trip this month 1 tow home 1 finally got it home on its own.After about 7-10 miles pressure goes...
Any one in the Atlanta area have a 35 Chevy 2 dr sedan
Anyone in the Atlanta area maybe south of Atl have a 35 chevy standard 2 dr sedan I need to measure some of the body so I can get back on mine Thanks
1957 283 short block I think is is 060 over but will check Had it in my 55 back in the 80's but changed to a 327 so it just sit.No side mount boss...
Need to replace bushing on my Posie spring shackle and need to know if the spring need to be held in the weight down position or jacked up...
How to you clear the dust cover on the axle to press it off on a 55 Chevy . Not enough room for clamshell doesn't seem like.Thanks
What ever happen no more photo in a while from him
Which way do they fit smooth side to the rear or the curved side to the rear facing the door.Thanks been off so long can't remember
How much does the side window go down trying to put power windows in because I don't have the org regulators on the 2dr standard sedan Thanks
On my Vintage Air unit on my 55 Chevy that I just installed both heater hoses are hot all the time.The heater vale is installed like the...
Can't use SignIn click to log on have to use quick navigation to log in and it is real jumpy while on the site.Maybe my computer after Chrome...
What tool is needed to install piece on door before handle goes on.It is swedged on somehow Thanks.It is a 35 Standard sedan
What does the contact pin that goes in the steering column to blow the horn on a 55 Chevy look like and when you put the tri bar on and tighten it...
Just got my 55 wiring back together and the only problem is when the dash lights rare on the tach light also when you rev engine up the tach light...
When I put the tail light bulbs in both wires are hot and the outside housing with the test light will show 12 volts on the housing but take the...
Put a new wiring harness in my 55 Chevy.Now the tail lights both wires tail and turn wires are grounded to the body with switch off.My engine...
Do you have to wire it through the alt or can you pick up another 12 volt battery source like cigar lighter.Hate to run that big alt wire inside...
Anyone have a vintage air unit for a 55 Chevy A couple questions.How do you run the hoses to the vents and what vents do you use for the outer...
Putting a sure-fit in my 55 Chevy and can't get the hard lines from unit to go out of where the org blower motor went.Been calling tech support...
What other websites are there for selling old drag race wheels and parts.Thanks
Bumped a set of wheels in parts for sale yesterday and today it is not on parts for sale page.What did I do wrong Thanks
What hi torque starter can I put on my 55 with a Lakewood scattershield made for the org 55 starter.A later housing won't fit in bell housing.The...
Need to know if I can lead pin hole in bottom of door on my 35 and do I need to tinning the frt and back since I'm taking all wood out and replace...
Separate names with a comma.