The Jalopy Journal
They look great, nice work. But why no drilled and tapped holes for the fuel pump stand, or block off?
I don't know about this show. That scene in the back room is sketchy to say the least. If you don't mind rubbing elbows with a bunch of car...
Why are you not using your original 1928 tank/ location? If I were lazy and cheap I'd just use the stock tank.
Got a 28/9 winter front for the roadster ! A winter front for a roadster? The motor can warm up but how about you? You gonna put a heater in the...
Thanks guys. Although the window more or less fit the car, it never seemed quite right. I have learned a lot from the posts.
And there it is. Any idea what windshield I'm working with here then? Guess who needs a new windshield?
Ok. I got some pics to show you all. Look at the dash: ( most likely a 1930/31 ) Look at the wood header: ( came with a pile of parts in the...
No the car's interior was non existent, and I'm piecing things together one at a time. I have my doubts if the front window / frame is the correct...
Hey Guys, Any 1930 or 1931 Model A coupe owners out there that could post some pics ( or advise on how the fitment should work )of the proper...
That pic was taken at the time when I was wiring the car, and that hose is just a length of canvas sleeve to ultimately cover the few wires....
Generator was polarized yes. But 97 I did have issues with the new generator making voltage. There may be something in what your getting at. The...
Good eye! Someone was paying attention. It's a Hexagon intake. Road tested it yesterday after the rotor change and now not only does it stumble...
Yes a ballast resistor is in place. I have actually touched the coil after each outing thinking the same thing and it's only warm to the touch. I...
Well, Here we go. Smack dab in the middle of the nicest summer we here in Buffalo NY have seen in my lifetime. I have had a intermittently poor...
I'm reaching out to Buffalo NY area HAMB'ers hoping to track down a replacement Ford flathead fan assembly (1942 - 1948 ). I was out for a drive a...
If you have access to a flux core then try it. It will do fine, but flux core welders are obnoxious in a home garage environment. They do make...
Mac's Auto parts has 600w oil (Part #: 16-16020-1) on the shelves and on line for $7.95 per quart. I was told by an old racer that he would...
Model A taillights on a fender less car[ATTACH] .
Craigslist near you. Hilton / Clarkston Add ID # 5591907093 Copy that number, go on Craigslist, auto parts, paste that number, see it, go...
Wolf, Have you any new update photos of the 283 to share?
Laying hands on a relic of a bygone era and breathing new life into it is at the core of traditional hotroding. In fact what Old Wolf is sharing...
Very nice work. That old girl is getting the works! Unless I missed it and you stated it else were. My Question to you is. What was the final...
Thanks Shoop. Thanks AVater.
Like the original post and the piston tops say, the bore is standard. Tough to figure out as suggested in post 2 , why would someone replace a...
Closer up.[ATTACH]
To the Flathead guys. Take a look at these pistons for me and weigh in on what you all think they are. Motor is a stock bore Ford 1946 59AB....
We should have a HAMB Sign in attendance sheets at local shows swaps and events.
I'll be there too. Try to not miss this swap. First time as a vendor. Out in the shed and the garage yesterday packing up that rusty gold.
Mike you are dead wrong. I only came here to rant cause i'm an honest man that did try to go through the correct channles by calling BDS tech and...
Rex read post 4. I measured before assembly. With a Mic and a bore gauge. didn't like what I saw and called BDS. The rep at BDS told me "to take...
Separate names with a comma.