The Jalopy Journal
I had 2 dirt track 350s in which those pistons were used and did not have any problems with them. My machinist (Wayne Calvert) recomended them for...
Well, I went back and read the other threads with "scam" in the title and I if I had read them before, then there would have been no need for this...
Thanks folks, I thought it sounded kinda fishy although I didn't know how it would work when I'm the seller. Surf monkey, since you are already...
Placed an add in the Whowon.com classifieds to sell a Street Stock dirt track car and this is a reply I received My name is john i am an auto...
The older ram style and the late 60s thru mid 70s down style manifolds all work with a left hand dipstick block. you can use the 78 and newer log...
You can either use the rubber end pieces or not with good results, but if you do use them, never use any kind of silicone. Silicone is a lubricant...
Very good advice and I apologize for my earlier outburst. After seeing the size of the guy on the video Wal Mart had of him buying tires with my...
I too was the victim of mail theft and ID theft lately. I guess I got my mail going to my new address a little too soon in connection with a move...
I would go ahead and tear it down completely. Most likely it will have worn valve guides, flat cam lobes and need some rod bearings. The parts to...
If you wish to use a small flywheel with that bellhousing, you can by cutting off the lower half of the three bolt starter mount that is cast into...
FH, I have a 76 Buick 350 that I plan to rebuild and put into a Chevy P/U. The timing gear cover is pretty much toast. I have 2 Buick V6 engines...
Hell has got circles??? Bummer!!
Ok, I'm chiming in as someone old enough to have driven daily and competed on both radials and bias ply tires. As a matter of fact, we are still...
Went to Abilene to take part in the Southern Challenge, a large 3 day IMCA race event. Didn't do real good, but didn't do too bad either. You can...
Correct Rocket 88, it is a vent tube baffle to prevent a sag during wide open throttle operation. He should be ok without it with a tall air...
You have either an open fusable link or dirty battery terminals. I would clean the battery connections first and if that don't help, I would then...
The Vortecs come in a 6 bolt per side on the intake design and a 4 bolts per side on the intake design. I don't have a lot of experience with the...
If you have a 351C or 351W it will work. 351M will not. The kickdown controls the shift points on an AOD so you will have to rig it to move with...
As K9racer stated the IMCA spec tire is about the only dirt track tire that would be acceptable for highway use. They are DOT approved, but only...
Hey Dan, I can help and will be happy to. Feel free to PM me about this to keep it off the main board. Just need to know where you plan to run so...
It does depend on how damp you get sweating or whatever. The output on most welders is about 50 volts. Dry skin is resistant to about 70-75 volts....
If all else fails, you may want to check for an internal combustion to coolant leak. What you described sounds like it could be a head gasket...
You can remove the regulator and its associated wiring. You will find that most of the wiring runs between the alternator and the regulator...
The 307 wasn't a bad engine although like the cost cutting nonhardened cams they came with, the blocks were all low nickel cast iron making them...
Some of the guys I race with have experienced problems with Fram filters on a SBC, but only with a blocked bypass. I never plug the bypass on any...
I had never heard before that that a shorter rod would give more torque at any RPM range. My understanding was that the longer rod was always...
OR, it could be a Pontiac 301 or a Olds 307,350 or even a 403. You never knew what you might get in those late 70s thru early 80s GMs. If it is...
Separate names with a comma.