The Jalopy Journal
I ordered a aluminum radiator for a 55 Ford Fairlane. It is a 4 row. I received it today. As I inspected it it is about 1 1/2" thicker then the...
I think I know the answer to this but here goes. 57/58 rears are 29 spline and 59-64 are 31 spline. Question is can the spiders be switched from...
I have a 57 Olds. with a 4 speed hydro. Problem is no high gear and free wheels on deceleration. I have been told this was common with the early...
For sale is a beautiful 57 T Bird that is my girlfriend baby. But it just don't get driven enough since we do have two so we've decided to sell...
I have a complete rear mount radio antenna complete with coax and gasket never installed. Brand new. 90.00 shipped in lower 48
I have a very nice 55 Chevy 3 piece front bumper with bumper guards with very nice chrome. $350.00 plus shipping
I have a nice driver quality 3 piece front bumper for a 58 Chevy. It has a small scrape on the lower right side that you need to get on your knees...
I think I know the answer but here goes. On a Borg Warner super T 10 trans. is there a tail shaft housing that offers a left side speedo. cable...
I have a pair of 348/409 W motor heads in good shape. casting 3819333
I have a pair of brand new never installed rear mount antennas for a 59-60 Chevy Impala or Belair complete with gaskets and one coax cable. 130.00...
For sale are several 58 Chevy Impala parts Including a good frame roof inner fenders and fenders and other parts. I'm listing this for a friend...
I have a complete rear mount radio antenna complete with coax and gasket never installed. Brand new. I bought for my 58 then realized my 58 had a...
I have a 1957-64 Chevy 4.11 posi third member in a P case date G 5 3. July 5 1963. The posi unit has a date of July 10 63 so it has the later...
Very solid 55-56 Ford car front crossmember. 200.00 plus actual shipping cost.
Earlier today (Sunday I posted for a wanted part for a 62 Chevy. A member Alex22 responded and gave me an email of someone with the part. The...
Very solid car with all rust repaired which was very minor. This car is a true barn find. Fresh 355 engine balanced with Thumper cam new clutch...
Does anyone know if Halibrand is still making the Torque Thrust wheels? I bought a new pair of 6" Torque Thrust about 12 years ago. I liked...
I have what appears to be a third gen. Pontiac 9.3 complete rear end drum to drum. Approx 63" wide +or- axle flange to axle flange. Ratio is 2.69...
I have a Pontiac 9.3 complete rear end drum to drum. Approx 63" wide axle flange to axle flange. Ratio is 2.69 open non posi and date code is B 5...
I purchased this car with the intention to repair,get running and sell as I already have 2 55's and 13 cars total.. The only rust area I have...
Parting 1955 Pontiac stainless engine parts etc. Side trim has been sold. [IMG]
I am going to be doing a roof repair on a 55 Chevy Hardtop. At this point I am not positive which way I'm going to go about it. At first I was...
I have a like new 32-41 3 bolt style point Mallory dual point distributor (2572101) like new. About 500 miles. I sold the car and kept this...
I have a very nice survivor right side headlight bezel with no dings. The side that is always dented. A very nice driver quality that should clean...
1965 Thunderbird landau with a 390. It has an aluminum intake and an Edelbrock carb. Rust free and drives nice. The car does have the skirts....
I have a new 55/56 Ford Fairlane front cross member from Goodell that I will not be using.$275.00 shipped lower 48.
Factory 2x4 intake manifold for Chevy 409 425 hp. in very good condition. No carbs
Very nice 30/31 model A Ford coupe frame. Horns and running board mounts intact. According to frame # this a 31 frame. No paperwork.
A very nice pair of 62-67 Chevy valve covers with the clips for temp. sender. $100.00 plus shipping.
For a Ford car I have the center link,idler,frame bracket,control valve and slave cyl. Been off the car a few years so may need o'ring...
Separate names with a comma.