The Jalopy Journal
I used 49-53 truck pedal set changed the clutch shaft to later type with a frame mounted pivot, no lever on the trans
Ex Wife
I tried mine and they worked the same however I clamped them down. I pulled the plugs and dumped and rinsed out the old crud and put in some new...
Dick Spadaro, search on here or fordbarn, often has the not reproduced stuff, NOS that areard to find.
'46 Subframe cutoff, put in backwards, locate determined after engine is correctly placed, cake, just have to make front of X to avoid starter,...
Like ol don says, I put my radiator behind the crossmember made room from there back, no cut firewall, back axle ends up where it ends up.
Like charlie said and the same number on the side of the driver side of block, then you use that VIN and if there is no red flaq when you go to...
41 Ford tonner, need to take a hammer to it, think someone missed a spot
2 things I notice, the fan mounted on the crank, thought it was exclusive to big truck. Also usually the oil filter is on the rear of the heads,...
pre-49 = 59 cast on bellhousing, cam cover distributor? distributor sticking out top, bolt on bellhousing heads say 8BA for car 8RT for truck...
8BA is car although no big deal, still a flathead but no clean out pan unless someone swapped heads. Carb should be a 94 series and have 8BA or RT...
Yeah git it, 8RT will say so on the heads, bonus if it is a floor shift light duty 78 series trans. If it,s a HD trans still good scrap after...
Save rear trans cover /trans mount, saddle, ujoint and even the squirrely pedals and master cyl. mount, you just never know... Vin # is on the...
MY machine guy thought leaving the bearing out was OK, I took out about 18 3/4", tested to 70 mph and smooth and I don't do over 50 so OK for me....
Leatherman
Jackstands and shims and a very good level. It will try to curl, so the shorter the tack the easier to slice with the cutoff wheel when...
Big lots or dollar general, $.99 x 5, fuica or magenta. Cool!
Other side up, look up "shield stamps" as I know of an art deco modular gas station building that had all kinds of trading stamp signs.
I had no tube so I made a column,1 1'4" roll bar tube. Tractor Supply has a flanged retainer bearing 3/4" inside I used. Restored my buddy's 39...
I heard something I never remember to try. I was told after welding the nut on the busted stud, jam wax up agianst it. Guy had canning parrifin in...
Update- I was block sanding the top decks, looks to be a crack in the passage below the normal crack, looks like it go's to the cylinder or in...
I have a 53 motor that had a bad bearing, haven't put it back together yet, don't need it
36 had rod mechanicals, 37 & 38 were cable brakes
So what is the story? Was the motor a runner that locked up ( because of bad oil pump) or is it a surprise package? I have lots of pumps if you...
It's not supposed to do that, shaft stays with the pump. Dried goo makes the pump hard to pull out sometimes, but it will come outa there. Shaft...
One bolt in the flex plate too long?
That 1/4" should be OK, If you have a snug fit on the splines try making a tight pin.
I tried a roll pin &broke it, coupler fit too easy on the pinion.I had a piece of about 5/16 rod, not hard, belt sanded until it almost fit, drove...
I don't know if they are reproduced, pick them up at swaps once in a while. I probably have some.
I inset mine about 1/8" sort of like 1a. I bolted everything up the whole car assembled so I had nuts, threaded bungs, crush tubes all tacked on...
Separate names with a comma.