The Jalopy Journal
[MEDIA]
New price. 35,000. Thanks. Call or text please. Thanks
For Sale: 36 LB flathead 39 tranny 32 rearend Mechanical Brakes 36 whire wheels (red) Front tires are Coker Firestones 6.00x16 Rear tires are...
[IMG] Sent from my iPhone using The H.A.M.B. mobile app
Change of wheels n tires [IMG] Sent from my iPhone using The H.A.M.B. mobile app
Or in Bruce's case 61 words! Sent from my iPhone using The H.A.M.B. mobile app
A picture is worth a thousand words. Or at least a hundred or so! Sent from my iPhone using The H.A.M.B. mobile app
What's cool about this is not only what was said already about Barn Find, the thread itself, but also that Corncob says...I did it...sorry about...
[IMG] My old 40. New owner said he may sell or would trade for a 1932 5W coupe! [IMG] [IMG] [IMG] Sent from my iPhone using The H.A.M.B....
Not sure yet. Let me know if ya find something cool to go to and I'll do the same! Sent from my iPhone using The H.A.M.B. mobile app
Thanks man! What's the next car get together your going to? Sent from my iPhone using The H.A.M.B. mobile app
Out beating around Springfield MO with my friend Bret Chrismer and found a photo op on our way to Chris Clark's shop! [IMG][IMG] Sent from my...
That fence poses no threat to the average man with 32" inseam! Sent from my iPhone using The H.A.M.B. mobile app
Yep I agree. Maybe 5lbs. Just the weight of the cast bearing carrier. Maybe 2-3lbs each. The locknuts on my setup would be lighter than the...
Well OK then... Sent from my iPhone using The H.A.M.B. mobile app
What's your reasoning for replacing the full floater setup and Lincoln brakes? Sent from my iPhone using The H.A.M.B. mobile app
I got a couple for an upcoming 32 pickup project but like everyone else so far, not a runner yet. But I've talked to several people that run...
Maybe a Hambster. I been wanting to test some flathead engine ideas. But not sure if that will come together anytime soon. Sent from my...
Nothing. I like to drive lots of miles and can't handle the whine! Sent from my iPhone using The H.A.M.B. mobile app
Was told that years ago racers would mark a line down the full length of the axle. 1-1/2 turns was usually failure! Yikes! If that were true...
Here's a stock one. Looks similar to me. This one doesn't have the bearing or race on it. But you can see the "snout" is thick enough to cut...
So it looks like a stock Ford carrier with splines cut into it. I'm sure it weakens it but with the bearing race on it, its like a sleeve that's...
So here's what see as far as the axles go. The flange looks like a custom machined piece with a ring welded to the inside that fits into the hub....
That's what putty is for. It would be fine for testing. Just build up when needed with epoxy or putty when testing. Sent from my iPhone using...
Sonic test would give you an exact answer. Most say keep at no less than .100" cylinder wall thickness. The sleeves look fairly thick to me but...
That block froze and busted most likely. Would be practice material if I owned it. That's a shame too. Not much you can do with that one but...
Whoops. This is the other side. [IMG][IMG][IMG] Sent from my iPhone using The H.A.M.B. mobile app
[IMG] Looked good to me Sent from my iPhone using The H.A.M.B. mobile app
That's right! Sent from my iPhone using The H.A.M.B. mobile app
Separate names with a comma.
The Jalopy Journal
