The Jalopy Journal
Ok folks an issue I'd like to resolve.
disc fronts and drums rear.
Booster and dual port master.
All corners are dragging badly and then the drums...
As easy as the title,anyone got a lead for a supplier for it?
I've tried all my usual suppliers to no avail.
Other makes are similar and close but...
Anyone have pics of Where these actually mount.
Using glass fenders but can't see that making a difference.
Ok going through mocking up the 42 Tudor.
New Bolt in parallel leaf spring and Mustang II (thinking it came with one or the other but just don't...
Fitting a MII in the 42 Tudor.
Coil spring cushion is too big to go into the spring cup but fits the lower arm perfectly...is that ok? Or do I...
New 3" drop axle and drop spring in my F3.
OT p/s and all new front end components.
Steering is responsive but seems 'light' or 'floaty'?
Sorry if its a repost but could be too good to miss....
Something to tax my brain when I try and make it work.
Anyone used a 302/Aod in a 41-48 Ford car?
Looking for engine mount placement and trans x member mods.
Had the usual 'Im working away,will send shipper,grace of God for helping me buy this for my son' crap about a car I have advertised but instead...
Finally got round to starting the front end install on my 38 GMC.
Aftermarket front spindles don't have cotter pin holes in them?
Is this a...
Putting either a 9 or 8.8" and parallel leaves under the rear of my 42 Tudor and getting ready to cut all the original brackets and hangers off....
Looking for ideas or experiences with a pourable rubber,silicon etc.
Would like to replicate this piece on my 37 GMC truck.
It will be poured 'in...
A post I placed on another forum has garnered a response from a 'Brit' who has what I need.
10, Arnett Avenue, Finchampstead,...
As you may have heard , Olds college is having a 100 car charity auction next June 21- 23 , 2013
Olds college is an important scholastic...
Anyone know of a disc brake conversion for a 9" with the 2" offset?
Pulling apart an old 9" for cleaning and general maintenance and found this lying in the oil.
Any ideas on what it is?
Checking out leaf spring kits for my 42 Ford and this company came up.
Any dealings,good bad or indifferent ?
Has anyone else come against the problem of brake drums rubbing against the backing plates?
I've checked bearings and the backing plate for true...
Installed a new disc/drum set up on my 51 F3.
Front calipers work well but the rear is an issue.
Push on the brake pedal and the shoes move like...
Just have to give Kudos to this company.
Fanastic looking,easy to install and a customer service like nothing I've seen for years.
Tidying up my crap I came across this in a ziplock bag.
Had a new rad built for the 460 I'm running in the 51.
Easiest way of covering the whole rad with fans was using 3.
Easiest way to wire them...
I have a couple of carter carbs with several screw threads in need of repair.
Anyone tried the Loctite thread repair with any success?
What do you use for fuel lines?
I have a fuel cell with AN8 fittings and have to run a complete line right to carb.
I've searched and found lots of relevant posts but no definitive answer.
Can I use 1951 F1 spindles on an aftermarket 'A' dropped axle?
Took a snowy drive down south a little way to pick up my latest project.
This was rodded in the late 60's and then shedded in the early 70's where...
I have a small bearing 9" and need to know if it's just the backing plate that's different for brakes between this and the large bearing.
I have a...
Got told today I should quit the hobby because I spend too much time working and with my family.
Some people obviously think finding the...
I've tried search but couldn't find anything.
Has anyone swapped in a newer front clip on a 1952 F3 and if so which one,or if anyone has an idea...
Separate names with a comma.