The Jalopy Journal
runs low 6's in the 1/8 mile
has also run 138mph at 9.86 in the 1/4
just changed the leaf spring straight axle to a dropped...
I am changing my leaf spring straight axle to a straight axle with 4 bar with coil overs.
My vega cross steering box will now be in front of the...
I need a tube gasser axle with a 4" drop
i need it a custom length.
Any one have any info. On what the et's and speed was of the aa/gas cars of the late 60's early 70's was?
Both 1/4 and 1/8 mile
I am installing a vw (sol-cal) type steering stabilizer on my anglia gasser.
straight tube axle.
i am mounting one end on the tube and one end on...
1948 bbc anglia drag car
94.5" wheel base
50/50 weight distribution
i am looking to change my par. Leaf spring front axle to coil overs...
Am going to switch from par. leaf springs on my tube axle anglia gasser to a 4-bar coil over set-up.
I can only seem to find a std. radious rod...
I Have A 1948 Anglia Gasser With A Bbc And Par. Leaf Springs And Speedway Axle.
I Have Been Battling A "duck Walk" In The Rear (like A Severe...
I have a bbc with an 8-71 blower and 2) 750 holley blower carbs. that are boost referenced (this is a street/strip car)
I am having idle problems...
I just picked up a set of 3.5" vintage cragar super trick front runners.
These are the 3 piece design that bolts together.
They leak air (a lot)...
looking for some info. on the correct size, font and locations of
period 65-69 gasser drag racing window lettering.
also any idea of a place to...
Any one know where to find some trunk weather stripping for a 1948 pop.?
On my 1948 Popular , there is a seam just above the drip rail.
I believe it is the solder joint for the drip rail.
My question is; is there...
1948 anglia gasser
rear fiberglass fenders
where the fit up against the body
would you use welting or seam sealer and paint over i
new to having a parachute.
i have a stroud with mechanical launcher.
if i pull the pin in the pre staging lane is there any chance...
Looking for info. on how the soft top attaches and where to purchase, or is it something that is beter served to let a conv. top shop do?
Hey, I need help again from the chevy gen v/vi experts.
I bought a 509 gen v w/ an 871 blower (carburated)(ebay)
I have a blown 509 chevy engine that I purchased. it was a 502 crate motor and was bored. all componants are new and were done at a reputable...
1948 Anglia pop.
Any one have a source for Anglia metal body replacement panels?
I need a rear valance.(the panel the trunk lid hindge bolts to)...
I am looking for a place to purchase the stanless mesh that custom grilles are made from. I see the finished product but can not find the wire...
Looking for recomendations for:
Chassis paint (semi gloss black)
will be covering encapsulated rust colored metal, bare metal and fiberglass...
Need someones thoughts on this.
I HAVE A 9" STRANGE FABRICATED HOUSING 58" LONG
I HAVE INSTALLED UNDER THE CAR
I HAVE CENTERED THE PINION NUT...
A couple of questions:
I have a 509 cu.in bbc with an 8-71 blower.
1- Are 2 vintage offey side mount breathers (about 5" long) enough? (1 each...
I have an old set of 14" wide anson slots that need to be refinshed.
Can anyone recomend a shop that i can send them to?
I have an anglia gasser recreation. have a speedway straiht axle w/ buggy springs. the questions i have:
1- on springs- shackle on front or...
Separate names with a comma.