6x2 top for 6-71 blower

I think we got a cool idea with this one. The lower plate bolts to the blower and then the top bolts to that. We are only offering the 6x2 for now but are going to make a 2x4 rams horn and a 3x2 in the future. The tops ae interchangeable so you can do a quick swap of your induction.

Of course this carries the EELCO name.

 

That kicks ass! its what i had in mind for a future build.. but how much does it cost... (that sounds so infomercial)

 

It lists for 299.99 and HAMBr's will get the 10% off as usual.
But if you act now!!!

 

are ya going to make a 8x2.

 

cool idea, is there a gasket between the two pieces or just use RTV to seal top plate to lower plate.

Sent you a PM with a question

 

There is a gasket. No Plans for an 8x2.

 

COOL.....
looks like a simple fix and great idea.

 

I forgot to mention this will work with Rochester 2 jets also

 

That looks top-notch man. Very cool.

 

How a 12X2? ...too much is just enuff....

 

that is so awesome marty....

 

Funny,
the same question was asked of me when I mentioned this to someone down here.....

 

Made a top similar in design to that about 10 years ago when a buddy had a 2-4 tunnel ram (with $$$$ invested scoop and carbs), then he bought one of those B&M 144 blowers with the 4v integral flange, so we made him a 2 piece top to fun his 2-4 setup. Looks good though.

 

An 8x2 could be done but I would need to see a lot of interest.

 

It looks way too big on top of the 6-71. The weiand 6-71 manifold looks perfect. I think you should go towards making it shape up nicer.....

 

how about making a base plate to bolt the 6-71 blower to my ford 289? then i could get the 6x2. any hope

 

That is mostly the camera angle. It is very close to the Weiand size. Also the case I have it on there doesn't have a rear bearing plate so that makes it 2" shorter.

 

How about a 3x2 for early hemi motors?

 

Do you guys have any 324 Olds crap? I didnt see it on your page.

 

while we're asking,

how about 2x2, 3x2 or 4x2 for topping a 471?

 

I think Weiand made two different types. One style pretty much like your's Marty and one that was a lot more compact.

Marty, are you ready to start taking orders for these? and What kind of timing for delivery?

 

My buddy just got his 6x2 set up saturday at Hotrodarama and it's a quality piece. The casting looks great and the machine work is top notch. I was over at your booth early sat and must say everything that I saw was high quality and very well designed and reasonably priced.. (the rotary table drill press story) It's good to see high quality Made in USA parts instead of the usual made overseas junk.

 

Hey thanks, It's nice to see guys who appreciate a quality made in USA part. We only brought a small selection to the show becasue we are working on going to SEMA this year. The blower tops are in stock now. i will add them to our online catalog later in the week. (I have about 6 new items to add)

 

Holy shit!!

What I would give to have a Weiand like that again!

 

Great item!!!!!!!!!!!!!

 

I just put one of the prototypes on Ebay. No reserve.
http://cgi.ebay.com/ebaymotors/ws/e...d=1,1&item=4569453365&sspagename=STRK:MESE:IT

 

Hi,

 

Hi, are the 6x2 top for 671 blower still available? if they are, I would be real interested in buying one, could you let me know. thanks, Mario DEAD MAN'S CURVE CAR CLUB

 

This thread is 5 years old!

If that is the Marty I purchased parts from....NO BUENO!

My eelco 6x2 manifold for the nailhead.....half of the holes didn't line up and had to be filled and re-machined

An ST400 flywheel I purchased looked like it had been welded by a blind man with a harbor freight stick welder.

And shipping??? That was the worst! promise after promise, then lies to cover lies on why I havent received anything yet.

Marty Lackner/EELCO get two thumbs down here.

 

....