Register now to get rid of these ads!

Fired up the '30 FORDOR today! -VIDEO ATTACHED

Discussion in 'The Hokey Ass Message Board' started by Mr. Cool, Jan 2, 2010.

  1. Mr. Cool
    Joined: Sep 12, 2008
    Posts: 170

    Mr. Cool
    Member
    from Northeast

    Well... after some Chineese Flexplate issues (Summit Brand SFI FLEXPLATE teeth shattered when cranking it!!--Ended up buying a B&M brand))....I was able to bolt this baby together this morning and fire her up!!

    I set STATIC timing to about 8* BTDC so she would at least start up...eyballed the rough idle screw, topped off the fluids and crossed the fingers!!!

    Turned the key...I bet the engine only rotated once and fired right up!!! Idle was pretty darn close as well!!! Ran the tranny thru the gears ---all looks good!

    I'm glad I didn't bleed the brakes yet or I would have been tempted to take her out in the 17* temp, snow on the ground, and no windshield yet!!!....in due time she'll be out and about!!!

    Here is a YOUTUBE short video of the car:

    http://www.youtube.com/watch?v=jTURv1E_pWw
    <!-- / message --><!-- sig -->
     
  2. low-n-slo54
    Joined: Jul 25, 2009
    Posts: 1,920

    low-n-slo54
    Member

    Sweet! Congrats on that.
     
  3. Lalos53Ford
    Joined: Jul 30, 2007
    Posts: 767

    Lalos53Ford
    Member

    Congrats!! Looks good. Now time to bleed the brakes and drive it. Make sure to bundle up!!
     
  4. pincher
    Joined: Sep 12, 2007
    Posts: 378

    pincher
    Member
    from Saginaw

    Nice, that BIG BLOCK look's right at home in their.
     

  5. brady1929
    Joined: Sep 30, 2006
    Posts: 9,273

    brady1929
    Member

    that hot rod is a beast!
     
  6. RUSTALOT
    Joined: Jul 17, 2009
    Posts: 199

    RUSTALOT
    Member
    from GA.

    Congrats sounds and looks great!!
     
  7. Nice work Tom, who would have thought a 4 door sedan could look so cool!! :cool:
     
  8. Mr. Cool
    Joined: Sep 12, 2008
    Posts: 170

    Mr. Cool
    Member
    from Northeast

    Thank You!

    Lookin' for another Fordor right now!!!
     
  9. lawbreaker2
    Joined: Aug 13, 2007
    Posts: 199

    lawbreaker2
    Member
    from ohio

    That is sweet looking. Good Job.
     
  10. 32SEDAN
    Joined: Jul 30, 2008
    Posts: 1,315

    32SEDAN
    Member

    Man you should channel and chop it! I'm guessing you're around 4' tall... :)

    Looks and sounds great man.
     
  11. ironandsteele
    Joined: Apr 25, 2006
    Posts: 5,921

    ironandsteele
    Member

    congrats on that!

    beats the hell out of a 350 any day!
     
  12. popsracer
    Joined: Mar 15, 2006
    Posts: 139

    popsracer
    Member
    from Sacramento

    Nice job. Nice car!
     
  13. lorodz
    Joined: Jul 26, 2009
    Posts: 3,727

    lorodz
    Member

    nice job sounds great
     
  14. vail72
    Joined: May 12, 2008
    Posts: 23

    vail72
    Member
    from Stroud, OK

    great job, congrats, now DRIVE!
     
  15. claymore
    Joined: Feb 21, 2009
    Posts: 896

    claymore
    BANNED

    Is that a rebuilt or crate engine? Generally the best practice on firing a new engine is to run it at 2500-3000 rpm for 15-20 minutes to break in the cam and lifters. Letting it idle is not the best idea. But good job on preparation as it started on the first crank.
     
  16. el Scotto
    Joined: Mar 3, 2004
    Posts: 4,699

    el Scotto
    Member
    from Tracy, CA

    Neato burrito! I've always thought a Fordor A-bone would make a bitchin' booze cruiser, yours is a neat hot rod!!

    Where's the test drive? ;)
     
  17. Dynaflash_8
    Joined: Sep 24, 2008
    Posts: 3,037

    Dynaflash_8
    Member
    from Auburn WA

    way too quite!

    Awesome car man!
     
  18. Mr. Cool
    Joined: Sep 12, 2008
    Posts: 170

    Mr. Cool
    Member
    from Northeast

    6" Chop and 3" Channel...I'm 6' tall and 250 lbs and fit pretty darn comfy in there!! :D



    Engine was TRANSPLANTED from another vehicle. Engine was a good solid runner when pulled. ...Did nothing internal. Engine already had a very mild cam installed and all I did was just a new intake, carb, distributor, oil pump and pan, valvecovers...


    Well...it's 2* outside this morning and snowing....I think it will be a little while before she gets on the road!
     
  19. Mr. Cool
    Joined: Sep 12, 2008
    Posts: 170

    Mr. Cool
    Member
    from Northeast

    Well..a snowy cold windy day today....got the egine properly timed, carb nicely adjusted and tranny topped off!!! Come on SUNSHINE!!!!
     
  20. AV8 Dave
    Joined: Jan 3, 2003
    Posts: 680

    AV8 Dave
    Member

    Don't forget the brakes! Great job and great video! Thanks for letting us be there! Regards, Dave.
     
  21. BStoltz
    Joined: Mar 30, 2009
    Posts: 123

    BStoltz
    Member

    hahaha kick ass man great video and that car is bitchin.......
     
  22. shoveled71
    Joined: Jun 3, 2007
    Posts: 159

    shoveled71
    Member

    Great looking more door, good job,sounds healthy. Spike
     
  23. Mr. Cool
    Joined: Sep 12, 2008
    Posts: 170

    Mr. Cool
    Member
    from Northeast

    Thanks guys!!! Appreciate it!!
     
  24. Mr. Cool
    Joined: Sep 12, 2008
    Posts: 170

    Mr. Cool
    Member
    from Northeast

    ANother walk around video I threw together... http://www.youtube.com/watch?v=BCzZWPmqJmw


    ----


    Took her out for a spin around the block last night...all is good!!! My face is still defrosting (no windshield and 16* out)...but ran, steered, shifted and stopped!!! Video to soon follow!
     
  25. 29 bones
    Joined: Sep 26, 2006
    Posts: 1,138

    29 bones
    Member
    from so cal

    congrats......now go have fun!!!
    Brian
     
  26. Mr. Cool
    Joined: Sep 12, 2008
    Posts: 170

    Mr. Cool
    Member
    from Northeast

    First test drive!!!

    http://www.youtube.com/v/SQpNsOGP_hs

    Pay no attention to the whining sound...I had an electric fuel pump...the noise drove me nuts!!! I have since installed a mechanical one!!!
     
  27. NortonG
    Joined: Dec 26, 2003
    Posts: 2,117

    NortonG
    Member Emeritus

Share This Page

Register now to get rid of these ads!

Archive

Copyright © 1995-2021 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.