Hot Rods mark viii seats in 64 t-bird

ok got it working
add the orage wire to the diver seat with bl/w wires and evething work

 

i am still promis whit my posts!!!!!!!

 

Glad you got them working
What's next on the list

 

not so fast
front and back dont work
look for front seat posin swicth

 

door shut
door open
seat occupied

 

That's all stuff in the solid state module. It wants input from everything and wants to control everything.

So far, I haven't been able to fool one of them into working

 

got the pass to work i have one wire left over bk/br
+ bl/w , bl/w , o , w/p , db/o
- bk , bk , gv/r

 

is it hard(possable )to blow out the memory morule

 

This might be worth a study.
It's for explorer but much if not all would be the same on the Lincoln. At least it will give an idea that is better

http://www.explorerforum.com/forums...you-wanted-to-know-about-memory-seats.382835/

 

The time I have into them I could used passing side module off 94-96 w/o memory the passin side works with the buttons
There's button on the bottom of the module to re set it I just learned wort a try.

 

Or go for the relays setup

 

button on it
didnt work
it the car with ever thing hookup clers memory but i dont have the car

 

need to bypass the memory mordul

i dont how to cut and past but it on explorerforum
so i not only thathaving a promble

 

Like I said earlier, I've not yet been able to fool a seat module into working. As far as I'm concerned you have to go around the module and make the motors work the old fashioned way. Maybe someone else knows how but I do not. Also in the old fashioned way, the switches were complicated polarity reversing units and that's that it was all in the switch. In the new stuff the switches are just simple center off style so you need a complex relay to reverse the polarity.

This is one way on how to control a DC motor that reverses.
There are others as well but this is pretty easy to follow.
Good for Windows and seats.

You'll need 2 relays for each motor you wish to control by each switch.
Where it gets tricky is when one of them seat switches has a position that controls 2 motors at the same time. Most of the time- if it's wired correctly for each switch then the switch will work the pair of relay automatically.

In this drawing the switches are hot and provide power to the relay's pulling coil, that's ok as long as the wires for the switch are the same size as the wires for the motor. Most of the time I'll set them up so the switches provide the ground to the relay's pulling coil.

 

i both one ebay for passerg seat
call me 763 283 1805

 

http://www.lincolnsofdistinction.org/vbulletin/showthread.php?4525-Power-seat-wiring

 

got it working on the dirver side
here how
used passing seat memory mod with the cable to the seat buttens
F4LB14A699
memory and cable for $25 on ebay
bucaues its upside down the cables are short and you have to duck tape mod to hold it done

does anbody no how to get spell check on the hamb
i had a stock 7 years ago

 

I'm trying to replicate this same scenario with these seats in a GM A body Buick. I tried calling the number in this link, but to no avail. I tried looking up the part number for the body side harness of the module, no luck. I'm looking for that plug to use to put power to modules on both sides and use seats. Memory harness, cheap on eBay.

Sent from my SM-G955U using Tapatalk

 

cabel you need it in the car
junk yard well cut it out

 

I got it. Now trying to find exact word to power up. I even got the memory switch.

Sent from my SM-G955U using Tapatalk

 

I went further back and read the comments. I now have the black with orange left over on passenger side. But black w orange in driver's side goes to memory switch. Left over on driver's side is
Red w/ purple, 2 white, grey w/ blue, black w/brown.

Sent from my SM-G955U using Tapatalk

 

pos and neg are the same in the posting for passing side
look at post #39

 

i didnt use memoy swich
your on owe from there