Projects Project 29 Phaeton

12V Power - check!

Sent from my SM-G930T using The H.A.M.B. mobile app

 

Toe in - fixed...shortened tie rod 1/2" each side.

Sent from my SM-G930T using The H.A.M.B. mobile app

 

Motors been sitting there for a couple years... glad I remember the oil pump / pickup.
No room for those fancy white boards w. Stuff to do list...

Sent from my SM-G930T using The H.A.M.B. mobile app

 

Gas-O-lene lines.
Dang, Bolts Metric....! Buy new ones tomorrow...ALSO -
Need fan belts, radiator hoses, bolts, coolant, DOT-3, black tape, 10-30w, alcohol free GAS, bolts (shocks) (mount) , brn wrinkle paint, make shift door locks (slide), post office.
Sorry made it my shopping list....

Sent from my SM-G930T using The H.A.M.B. mobile app

 

Don't have the tool to get those races off.
Was going to be lazy and drive it to the show on Saturday but then I'll probably ruin the bearings...
Maybe I'll throw the sucker in the oven.
COE - 400F
Aluminum 2.73 - steel 1.63....
Next project - while It's baking.

Sent from my SM-G930V using The H.A.M.B. mobile app

 

That was FUN...
Baked @ 275 30min.
Still a &!+(# without a press..........

Sent from my SM-G930V using The H.A.M.B. mobile app

 

I use my build thread for a to-do list quite often.

Hey, where did you get that wire loom? It looks GREAT!

 

BRAIDED EXPANDABLE SLEEVING RATTLESNAKE
TECHFLEX
(on e-bay...)

 

Hoses n' belt.

Sent from my SM-G930T using The H.A.M.B. mobile app

 

If you like good brakes, and you don't like that new Billet stuff.
There's few better-looking calipers than these...

Sent from my SM-G930T using The H.A.M.B. mobile app

 

Pressure regulator plumbed.....nah...
Manifold hose smashed / cut somehow...


Sent from my SM-G930T using The H.A.M.B. mobile app

 

Xhaust.

Sent from my SM-G930T using The H.A.M.B. mobile app

 

Good Night!

Sent from my SM-G930T using The H.A.M.B. mobile app

 

Not going to the show tonight.
Well I am......not the tub.
Not going to rush it now...
would be great to show up in a bonfire..
45 PSI fuel ...!
+ 80 bucks for 6 feet on AN6!!
GAS PEDAL.
Bleed brake system.
Cotter pin / torque all joints.
FILL ALL FLUIDS...
Check gaskets first.
O2 sensor (gotta find a spot in the.
"Exhaust system."..)
KILL SWITCH!

But it's close!

Sent from my SM-G930T using The H.A.M.B. mobile app

 

Windshield adjustment...

Sent from my SM-G930V using The H.A.M.B. mobile app

 

I'm Lucky! / Stupid (it was raining outside!..)
Hanging the "conduit" B4 I took the opener down . Noticed the plastic plugs fell apart...the opener plastic seems kinda brittle too....wonder what caused that.

Windshield?
Still got the pieces I chopped out. Easy peasy...

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Oh MISSED THE HILBORN!!!
TINY SCRATCH ON THE RADEATER...
I AM LUCKY!

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Wow^^^ it's like it was guided past the Hilborn!

 

I know.....!
Plastic coupler gone....
Dunno What's up with da Plastic?

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Picture

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Happy with that...!

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Doing something I'm good at...
sitting down, staring at my car.
A lot of times, if it looks right, it works right...................?
Paralell Just LOOKS right....

Sent from my SM-G930V using The H.A.M.B. mobile app

 

OT but still kinda project related....
Did some research on Plastic Failure...
I'M THINKING WELDING IS THE CULPRIT...

Factors That Cause Failure
A variety of factors both inside and outside of the molding process can impact the quality of a plastic part. Assuming that there are no issues with design, the root cause of plastic part failure usually lies in one or more of the following areas:
Depending on the stage and conditions at which a problem occurred, the following types of part failures are possible:

Mechanical failures are caused by an applied external force such as tension, compression, or impact. If these forces exceed the yield strength of a material, the part can deform, crack or break into pieces.

Thermo failures occur when parts are exposed to extreme temperatures. Too high a temperature can warp, twist, melt, or burn the materials. At low temperatures, plastic becomes brittle.

Chemical failures occur when chemicals causes the plastic to break down. Elevated temperatures, existing stress, or mechanical load on the part will amplify the effect of chemical exposure.

Environmental failures are caused by factors such as humidity, ozone, ultraviolet light radiation, and pollution. The effects can vary from a change in color or a slight crazing or cracking to a more severe breakdown of the polymer structure.

----------------other site----------------
During machining and processing of metal materials by means of welding and allied processes, gaseous and particulate hazardous substances are formed. Ozone is one of the important gaseous hazardous substances. Ozone (O3) is formed by ultraviolet radiation from the oxygen in air.

 

Henry made the holes already....
Might cut them out and move down...?
1. Hi/Lo, turn R, fogs.
2. Hi/Lo, turn L, horn.

Twist 1, Twist 2, 4 Bolts...
All that stuff comes right off.



Sent from my SM-G930V using The H.A.M.B. mobile app

 

Sometimes it's good to slow down.
So stoked about Henry's puka.
I almost
1. cut it move it down & Welded
2. Step drill and fancy meassure...
3. Think I'll borrow a hydraulic hole punch from the electric boys at work.


Sent from my SM-G930T using The H.A.M.B. mobile app

 

Paint stripped that ugly green off.
"Military grade" under it.
Cut the flange off in the lathe on one.

Sent from my SM-G930T using The H.A.M.B. mobile app

 

Main power breaker bracket...
Tricky piece to mount!
First time it was upside down...!
Had to cut it an re weld it...


Sent from my SM-G930V using The H.A.M.B. mobile app

 

Snöre...
Grill was off by 1/2"...i think?

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Now I got power...

Sent from my SM-G930T using The H.A.M.B. mobile app

 

Let there be light...

Sent from my SM-G930V using The H.A.M.B. mobile app