Register now to get rid of these ads!

Mark Yac's Recent Activity

  1. Mark Yac liked David Gersic's post in the thread Technical Small Block Chevy 12 and two timing tab issues.

    With the engine not running, you find TDC with the piston stop. That lines up the line on your damper with 0 on your timing tab. With...

    May 26, 2019 at 10:43 PM
  2. Mark Yac replied to the thread Technical Initial timing degree for small block chev w points.

    Forget the vacuum method for now. Too many techniques mentioned here..Ya got the boy confused. Put damper timing mark at about 10 *...

    May 26, 2019 at 10:10 PM
  3. Mark Yac replied to the thread Technical Small Block Chevy 12 and two timing tab issues.

    Where is your rotor when your TDC marks are lined up?

    May 25, 2019 at 10:47 PM
  4. Mark Yac attached a file to the thread Technical Help gm 350 fuel pump.

    You want to fab or buy something like this, pictured. Notice the fill neck is grounded to the car. Don't bother going to the Zone or...

    100_1959.jpg May 25, 2019 at 10:39 AM
  5. Mark Yac liked dcs13's post in the thread Technical pinion angle coil over and ladder bars 55-57 chevys.

    "generally" speaking I use the 3 up 3 down method. I try to get the trans at 3 degree's up and then set the pinion at 3 degrees down....

    May 24, 2019 at 10:29 PM
  6. Mark Yac replied to the thread Technical Help gm 350 fuel pump.

    Fuel cells don't have vented caps. They are for racing and rollover protection.Yours is in backwards. WHAT IS INSIDE IT? BTW, is that...

    May 24, 2019 at 8:25 PM
  7. Mark Yac replied to the thread Technical Help gm 350 fuel pump.

    Did you look in the cell and view the back side of the out fitting? (third request)

    May 24, 2019 at 3:02 PM
  8. Mark Yac replied to the thread Technical Help gm 350 fuel pump.

    You looked at the outlet from the inside? As Jim said, where's the vent? Fuel sales (cells) need an outside vent and an anti- rollover...

    May 23, 2019 at 5:31 PM
  9. Mark Yac liked Nailhead Jason's post in the thread Projects Welding on NEW gas tank question..

    for the love of god, do not use a that tank sealer crap on it. If you have a new tank it does not need to be sealed. Its a new tank,...

    May 22, 2019 at 11:16 PM
  10. Mark Yac replied to the thread Technical Gear Ratio recommendations..

    Probably be fine...in third! Lumpy idle cams don't like to cruise down the road at 1800. 373 or 3.90

    May 22, 2019 at 9:58 PM
  11. Mark Yac liked David Gersic's post in the thread Technical Help gm 350 fuel pump.

    When mine failed it leaked gas on the floor. I’ve heard of others failing and leaking gas in to the oil pan. Could be on yours it’s...

    May 22, 2019 at 7:58 PM
  12. Mark Yac replied to the thread Technical Help gm 350 fuel pump.

    ....that's in there backwards. The fittings on top are for a return system and a vent that goes forward and under the car (outside the...

    May 22, 2019 at 7:56 PM
  13. Mark Yac replied to the thread Technical Hurst shifter handle question..

    Everything comes out the bottom, or rear , if you pop the end plate off.

    May 21, 2019 at 9:53 PM
  14. Mark Yac replied to the thread Linda Vaughn, Miss Hurst picture thread..

    I don't see anything on her page now, but I did read it last night. Better just be cautiously optimistic for now.

    May 21, 2019 at 8:38 PM
  15. Mark Yac replied to the thread Linda Vaughn, Miss Hurst picture thread..

    Linda is fine . This came from an old post on F/B that got kicked up , accidentally. See Traci Hrudka's profile on F/B..Yes, Joe's...

    May 21, 2019 at 8:27 PM
Register now to get rid of these ads!

Archive

Copyright © 1995-2013 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.