Hillbilly Werewolf's Recent Activity
-
Hillbilly Werewolf liked Okie Pete's post in the thread Projects Everyone remembers an idiot.
I like the horse collar. Without it the car losses its identity. But I seem to be out numbered in that thought.
Mar 28, 2024 at 12:59 PM -
Hillbilly Werewolf liked j hansen's post in the thread Projects '51 Desoto Custom.
Looks good [ATTACH]
Mar 28, 2024 at 4:31 AM -
Hillbilly Werewolf liked oldiron 440's post in the thread Projects '51 Desoto Custom.
[ATTACH] [ATTACH] Just for comparison, if there was ever a car begging for a chop top it was this one.
Mar 28, 2024 at 4:31 AM -
Hillbilly Werewolf liked drtrcrV-8's post in the thread Technical Flathead Distributor on a Banger???.
Sure would be nice to see this on the "Banger" thread, especially if accompanied with a "How-to-do"(with pictures)!
Mar 27, 2024 at 5:14 PM -
Hillbilly Werewolf liked RodStRace's post in the thread Projects 49 Plymouth.
Check the rockers, the floor around the base of the A pillar/front of the door and the area where the trunk floor meets the sides. Rust...
Mar 27, 2024 at 3:46 PM -
Hillbilly Werewolf liked squirrel's post in the thread Technical Mallory YC 310 Installation Help.
Probably with the clips on the sides, and the lump and condensors situated so they clear stuff that might be in the way. The rotor...
Mar 27, 2024 at 6:43 AM -
Hillbilly Werewolf liked 27 MoPar T's post in the thread Projects 1927 MoPar Powered Model T Coupe.
In the way of suspension and improving driveability I finally Installed a panhard bar on the front axle. No more chasing a hand full...
Mar 27, 2024 at 6:36 AM -
Hillbilly Werewolf liked 27 MoPar T's post in the thread Projects 1927 MoPar Powered Model T Coupe.
Once I had the manifold ready to install things snowballed. I ended up borrowing a set of Stromberg 81's and got to work getting...
Mar 27, 2024 at 6:36 AM -
Hillbilly Werewolf liked 27 MoPar T's post in the thread Projects 1927 MoPar Powered Model T Coupe.
Ended up driving and enjoying some cruises and meetups in the car for the remainder of the summer. All together the car has been a dream...
Mar 26, 2024 at 8:26 PM -
Hillbilly Werewolf liked goldmountain's post in the thread Projects 1927 MoPar Powered Model T Coupe.
I just went and measured the engine compartment on my T coupe. A Mopar flat six would fit. You are a bad influence.
Mar 26, 2024 at 8:22 PM -
Hillbilly Werewolf liked 27 MoPar T's post in the thread Projects 1927 MoPar Powered Model T Coupe.
After a few joy rides around the parking lot at my shop. Flushed with joy and motivation. I took that momentum and finished up the...
Mar 26, 2024 at 8:21 PM -
Hillbilly Werewolf liked 27 MoPar T's post in the thread Projects 1927 MoPar Powered Model T Coupe.
Being a glutton for punishment I also decided to have a camshaft ground at Delta Camshaft in Tacoma to try and eek out a couple more...
Mar 26, 2024 at 8:13 PM -
Hillbilly Werewolf liked 27 MoPar T's post in the thread Projects 1927 MoPar Powered Model T Coupe.
Well this winter has been productive! To start things off I ended up scoring an Edmunds Custom 2x2 manifold locally. @Dynaflash_8 found...
Mar 26, 2024 at 8:05 PM -
Hillbilly Werewolf liked hotrodA's post in the thread Technical Cured my flathead's occasional overheating! Updated. 3/26/24.
Been inactive for awhile except for some fiddling with small things on the engine. Ran some gauge wires, along with under dash...
Mar 26, 2024 at 2:35 PM -
Hillbilly Werewolf liked gatz's post in the thread Art & Inspiration Interesting inexpensive Craigslist cars.
41 Studebaker Champion, Brownell, KS $1500 [ATTACH] https://www.facebook.com/marketplace/item/426050169875634/
Mar 26, 2024 at 1:25 PM