gary macdonald's Recent Activity
-
gary macdonald replied to the thread Technical Where to find narrow (2”) by 2” drop lowering blocks?.
Make them. You can also set your differential forward or back a little if needed .
Apr 19, 2024 at 5:46 AM -
gary macdonald liked MCjim's post in the thread Technical Where to find narrow (2”) by 2” drop lowering blocks?.
A B C... [ATTACH]
Apr 19, 2024 at 5:45 AM -
gary macdonald liked BJR's post in the thread Technical Top hood hardware ?.
Here is how I held down a 2 piece hood top on a 32 Roadster I am building at work.[ATTACH][ATTACH][ATTACH][ATTACH]
Apr 17, 2024 at 8:13 AM -
gary macdonald liked ollucky4848's post in the thread 1947 Ford Coupe SOLD SOLD SOLD SOLD.
PRICE REDUCED ... PRICE REDUCED ..$18,000.00 OBO MOTIVATED TO SELL
Apr 17, 2024 at 5:36 AM -
gary macdonald liked ollucky4848's post in the thread 1947 Ford Coupe SOLD SOLD SOLD SOLD.
For sale is my 1947 Ford coupe .. this Ole girl is a driver !! its been all over Texas, Oklahoma and Kentucky on rod runs .. engine is a...
Apr 17, 2024 at 5:36 AM -
gary macdonald liked hotroddon's post in the thread E Z steer: my bad experience.
The Vega replacement is from UNISTEER - NOT EZ Steer Nice looking car
Apr 15, 2024 at 10:42 AM -
gary macdonald liked 2345.coupe's post in the thread '37 Willys Sedan.
ttt
Apr 14, 2024 at 3:42 PM -
gary macdonald liked 2345.coupe's post in the thread '37 Willys Sedan.
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]...
Apr 14, 2024 at 3:42 PM -
gary macdonald liked ROADSTER1927's post in the thread Technical Banjo rear with spring in front.
This one is done with the spring in front. it let me pot a bigger fuel tank in the back and is also what supports the rumble seat. I...
Apr 14, 2024 at 3:39 PM -
gary macdonald liked Goob Taylor's post in the thread 21 stud flathead and 32 trans.
[ATTACH] 21 stud flathead, turns over. 1932 ford transmission. Pictures show details $350 Call/text 615- 587-129three Middle tennessee
Apr 14, 2024 at 3:37 PM -
gary macdonald liked 396skip's post in the thread Kinsler SBC Injection.
SBC Kinsler FI Setup with all the parts shown.
Apr 13, 2024 at 6:29 PM -
gary macdonald liked Frames's post in the thread FLATHEAD JAHNS PISTONS. 3/8 X 3/8 WITH RODS & BEARINGS.
296 C I D. 3 3/8 bore. 3/16 low crown. [ 4 1/8 stroke ] NEW .010 bearings. Rods look good. $300.00 FREE shipping in the good ol U S...
Apr 13, 2024 at 6:25 PM -
gary macdonald liked RB35's post in the thread Model A Frame no title.
btt Price reduction to $150.
Apr 13, 2024 at 6:23 PM -
gary macdonald liked RB35's post in the thread Model A Frame no title.
btt
Apr 13, 2024 at 6:22 PM -
gary macdonald liked wheeltramp brian's post in the thread Technical 1941 ford coupe trans removal question.(finished).
Thanks, man. I'm glad it worked out too. With the previous trans was a little hard to shift into all the gears. But third gear was very...
Apr 13, 2024 at 6:21 PM