Register now to get rid of these ads!

Corn Fed's Recent Activity

  1. Corn Fed replied to the thread Features Corvette hot rods - picture thread.

    Hah! I bet after the top loader swap he got tired of calling the tow truck to pull him home because of a shelled tranny.

    Oct 14, 2019 at 3:28 PM
  2. Corn Fed replied to the thread Features Corvette hot rods - picture thread.

    That's crazy. Why would anyone put a Ford top loader into anything besides a Ford chassis? I could see using a Cad or Buick 3spd, but...

    Oct 14, 2019 at 3:13 PM
  3. Corn Fed liked 26Troadster's post in the thread Motion Pictures Your favorite (H.A.M.B. friendly) movie cars..

    never noticed the mopar but i sure hope that damn train runs late the next time i see that movie. lol

    Oct 14, 2019 at 2:54 PM
  4. Corn Fed replied to the thread Projects Introduction and needed guidance....

    What width are the 17" rims? I think the 16" are 4" wide.

    Oct 14, 2019 at 2:23 PM
  5. Corn Fed replied to the thread Motion Pictures Your favorite (H.A.M.B. friendly) movie cars..

    Nobody's mentioned the Mopar in Cool Hand Luke yet..... https://www.youtube.com/watch?v=DvT5yB0RrMo

    Oct 14, 2019 at 2:12 PM
  6. Corn Fed replied to the thread Hot Rods Project parts value help.

    Yep. Those are 30-31 Roadster. The doors don't look too bad either.

    Oct 14, 2019 at 1:58 PM
  7. Corn Fed replied to the thread Projects 327 in a '33 Coupe.

    Everybody thinks their 33-34 firewall is so sacred and shouldn't be cut. BLAH. Cut it back a few inches, give yourself plenty of room,...

    Oct 14, 2019 at 1:02 PM
  8. Corn Fed attached a file to the thread Hot Rods Project parts value help.

    Yep, bad choice.. Y-blocks are too heavy for an A. I guess after 15 years of haulin' ass down the road I should pull this boat anchor...

    4.JPG Oct 14, 2019 at 12:52 PM
  9. Corn Fed replied to the thread Hot Rods Project parts value help.

    At $500, you wouldnt be getting much of a deal. A 272 is not a desirable Y-block so it doesnt really have much value and might be hard...

    Oct 13, 2019 at 10:39 PM
  10. Corn Fed replied to the thread Technical Saved from scrapper.

    I think you might have a Model T big truck axle there. The spindles and general shape of the axle look T, but it has pads for parallel...

    Oct 12, 2019 at 11:02 PM
  11. Corn Fed replied to the thread Projects buying an ole can a beans:my 29 ford.

    Sweet! Your new shop is going to seem huge....for about 6 months. Before you know it every square inch will be filled with more stuff...

    Oct 12, 2019 at 10:36 PM
  12. Corn Fed replied to the thread Projects Introduction and needed guidance....

    Here's my 2 cents: Many people have stated to flatten the rear crossmember. That might be ok if you were still in the initial phase of...

    Oct 11, 2019 at 10:11 AM
  13. Corn Fed attached a file to the thread Art & Inspiration Vintage rectangular photo thread.

    I've posted this before on the hot rod Corvette thread, but here it is again. This is my Dad's '62 taken in 1972. [ATTACH]

    62 Vette.jpg Oct 11, 2019 at 9:38 AM
  14. Corn Fed replied to the thread Technical Good deal or not?.

    Check the seating area to make sure they werent chewed up during removal. Years ago I had some tires switched to different rims and the...

    Oct 9, 2019 at 10:22 PM
Register now to get rid of these ads!

Archive

Copyright © 1995-2020 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.