I am looking at buying a straight 6 motor from a guy that came out of a 1951 GMC pickup. Does anyone know what cubic inch that would be and if a late model trans could be bolted onto the back of it? what are some physical features you can see from the outside to determine information on the motor?
GMC motors are easy to identify, just look at the stamped no. just behind the distributor, the first 3 numbers are the displacement. Example: F248------- is 248 c.i.
The 248 -270-302 GMC is three longer than the chevrolet 235/261s etc...... Fukk pressure oiling with insert bearing etc makes it a upgrade from a 235 etc....... The 302 can be bored to 322cu inches making them a flathead killer........
From 1939 and up, the GMC six cylinder was a high pressure insert bearing engine - initially 228 and 248 cubic inches. Chevrolet did not adopt the full insert bearing engine until 1954. This results in their similar appearing dash clusters having an exception of maximum oil pressure gauge reading of 60# or 80# for GMC and 30# for Chevrolet. Almost all Canadian built GMC pickups prior to 1953 used the Chevrolet 216 engine, not the 228 and 248 GMC type placed in U.S. trucks. The Canadian Chevrolet using the larger GMC 228 and 248 was the "Maple Leaf"! http://www.antiquechevytrucks.com/Content/Orginal%20Restoration/advancedesign_main.htm
What is it going into?? Car or truck? A later transmission may or may not bolt to it. There are stock bell housings that would do the job, you may run into rear mount problems.
Cant speak for him, but I think he is interested in it for a model T rat set up. Thank you for your help Donnie
I guess engine mounts would not be a big problem. There are stock bell housings that will bolt most any later model GM transmission to that engine. Bell housings from Chev 216, 235 & 261 will fit the block. Just pick the transmission pattern you want.
well, gosh - if it's a RAT ROD you're building, dont' worry about mounts...just weld the crap out of everything - "you don' need no stinkin' tranny mounts"
Man, you got that right, Bubba. In 1959, I had full-fendered '27 T sedan on '31 'A' rails, 3/8X3/8 (296 C.I.) Merc flathead with all the sing: ported & relieved, full polish thru ports, Silvolite pistons, aluminum flywheel, 4-jugger w/ Stromberg 97s, Harmon-Collins Du-Coil, '40 rear w/4.44s. This thing was a rocket out of the hole. One evening a '38 Chevy Coupe pulls up, races his engine, (no hood sides, I could see & hear it was a six) But it had this loooong row of carbs...Light turns green, I rev to 4,000 RPM and pop the Auburn sticker. I'm at the other side of the intersection, almost ready to shift, when this Chevy comes by me like he was shot out of a cannon. Zzzoooom! Then he shifts. He's gettin real small, I check to see if I'm in reverse... He pulled into the Sahara gas station, and I followed. This Chevy had the full house. 302 GMC truck motor (that's what he called it) punched an eighth, McGurk cam & rockers, McGurk intake, (5 97s, count 'em!) and a whole slew of stuff. Torque Town. Nice feller, he said "You really had me outa the hole, that's one fast flathead!" I said, "Yeah, had you for at least 10 feet!" That Jimmy ate more than flatheads. I parked my T, and we went ridin' in his Chevy...we sawed off everything that came up alongside. One '50 Olds Coupe (J2 mill, beefed hydro) went out to 10th street with us, (this was gonna be a fast one) That Olds pilot got a good study of the '38 Chevy taillights! I would still build a 270 or 302 GMC mill today. Hard to find...
Donniearcher is the guy I may be doing a deal with. He has I guess from the info above a 228 ci. My plan is to put it in my wife's 33 chevy tudor. Not a R*t Rod. Its just a traditional hot rod. Motor and tranny mounts are not a problem. i can build them. What I am cuerious about is putting a turbo350 or something of the sort on it. I want to know if they will bold up. If not what will it take? I want a cool straight 6 hiwhway cruiser with more than 70 on the top end.
No problem putting a modern auto tranny behind it. Buffalo is your answer. http://www.inliners.org/buffalo/index.htm This is what it looks like when installed . . . Charlie Hardin's 54 GMC Another couple of shots . . . . Other side . . . Scooted down the road nicely and sounded great!