Projects 1930 model a

I was admiring the brake/clutch pedal mechanisms myself ,,there's a lot going on in a small area,,

 

So far no problems. However is not on the road yet

Sent from my SM-G930V using The H.A.M.B. mobile app

 

..


Sent from my SM-G930V using The H.A.M.B. mobile app

 

I hope it works as well as it looks, I still think it is a great space saver and if over built should be reliable with minimal flex. Bravo.

 

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Fitted hood and radiator today... good day!

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Wow - that's looking really good. Love the color too

 

About half done with wiring now and i am pretty happy with the altitude now that it is back on the ground!

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Looking great JT!!

 

I think it looks perfect.

 

there's a new thread on here how tires and with stance make a car. your car is a perfect example of that, nice job it needs nothing else

 

Looks the balls- nice job!
( East Coast term for Pissah!)

 

That be wicked pissah

 

Thanks man

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Love both of these pictures, can't decide which I like best.

 

You'll be amazed at how much better she rides with a little wider tire ( and the smaller diameter makes the whole car sit better, IMO)

 

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Nice coupe, be sure to check those starter bolts often. That engine in a boat application has a bracket that mounts to the block on the threaded hole by the fuel pump and the long bolt that holds the starter together. With out that support it will loosen and sheer the starter mounting bolts. Seen it happen many times, just my 2cents.

 

You are totally right on that. I have this motor in my 36 Ford pickup as well broke two of those bolts before I got it squared away. Just found a bracket the other day for this one

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Got the header back from ceramicoating today..

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Not to knock your thread off track, but I just bought a 30 Briggs. I am building a nice banger engine and this will be my project. I have been following yours and like the way it turned out. I will start a thread on the build later as it will be a couple months before I start.

 

Great place to start. Add your general location to your profile so people can recommend local sources as time goes on.

Charlie Stephens

 

Coolant lines today.



Sent from my SM-G930V using The H.A.M.B. mobile app

 

Having to share shop space with a crusty old 47' convertible... kids!

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Can you post a pic of that bracket?

Thanks

 

JT, how much did you lower the front end and how did you do it? I just looked through you thread and didn't really see how. I am preparing (mentally) to cut off the mustang 2 on my 30 Tudor and want it to look like yours. Thanks, Paul .

 

4 inch drop bell axle... worked pretty good so far... although I haven't driven it yet..

Sent from my SM-G930V using The H.A.M.B. mobile app

 

She lives!

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Sent from my SM-G930V using The H.A.M.B. mobile app

 

Sent from my SM-G930V using The H.A.M.B. mobile app