i have a 46 chevy 1 ton plus wrecker. It has a 235 chevy motor in it. My friend says he has another 235 he will sell me. I have in the back of my mind it is a 216. It is in a 47 chevy 3/4 on long bed. The 235 i have has a different place where the top radiator hose hooks up. The one my friend is attachec directly below the radiator center. Can someone help me out on how to tell the diference between the 216 and the 235? Also will a starter off of a 216 fit on a 235? His truck is for sale.
216 side cover tin goes right up to the valve cover, 235 it ends at the top of the block. 235 splash oiler has a triangular tin plate just above the pan rail behind the exhaust pipe, the pressure lubed engines don't have it.
wrong, 54 to 62 235s have the short push rod side cover because the early 50s 235s are bored out 216s and have the tall cover
I have to say wrong to both of you. As a big truck nut, I have had several unrestored untouched 1946- 1953 2 ton trucks. The 2 tons always used a low oil pressure 235 until 1954. The 1-1/2 tons used a 216. The 1940's big truck 235's still had short push rod covers just like the better 1954-up car truck engines, but they had the valve cover held on with 2 nuts on top instead of 4 on the sides like 1954 and up 235s. They still had the triangular oil pressure piece near the exhaust pipe just like a 216. The early low pressure/splashed oiled 235 is potted by==short push rod cover, two nuts on top of valve cover, and triangular pressed steel plate on driver's side just like a 216. Also the head is a little oddly shaped on the passenger when compared to later 235s. The starters should interchange. But the 1955 up 12 volt starter has a different number of teeth on the starter and ring gear! This is a photo of a 216 or low oil pressure early 235. Note the small stamped piece of steel held on by three "stove bolts" bolts/flat head screws, just below the exhaust flange. That is only on the splash oiled engines. The short stamped steel push rod cover as seen on this 1955 up full pressure 235 engine is also on the very early 235 big truck engines. If your push rod cover goes clear up over the spark plugs, then you have a 216 engine. Also the full oil pressure 235 and 261 engines will NOT have the small stamped piece of metal just below the exhaust manifold. This engine is a 216. The tall pressed steel cover that extends over the top of the spark plugs is the dead give away. Also any 216 or 235 engine with this type of valve cover is going to be splash oiled--- with the exception of the 1953 car 235 engine.
Even the 1953 car 235 engine is splash oiled if it was not a Powerglide car. I know, I own one. #3701946 http://www.inliners.org/becks/BCN2.html
Wrong The 235 with the tall side cover was a truck engine. In 1950 the power glides had a 235 with the short side cover.
Wow, my head is spinning. I have a 48 1-ton (that's new to me) and thought it had a 235 in it. Now I need to check... and see if I can even make any sense of it.
I will check the casting numbers tonight. I a pix i snapped earlier on my cell phone it looks like i see a 848 with a G2 to its top left then a 850 below. Is this the engine serial number? Where would the other numbers be located ? Thanks to all HAMB folks for the help!! I will post some pix soon of my pride and joy. Wreckerman
The s/n is stamped on the pad just behind the distributor most likely its not a 216 but a 56 or later 235 http://1954advance-design.com/Web images/casting-code-photos/codes-ser-nums.html good luck
If you have the correct exhaust manifold that came with the engine, the exhaust outlet on a 216 points straight down. On the 235 it points down at an angle. Also I don't ever recall a 235 with a side pan going all the way up to the head. I have a 1946 216, a 1950 235, and 2 1954 235s. The 1950 235 is the low pressure, Babbitt bearing, straight 6 and the side pan only goes up to the bottom of the head just like the 1954 235s.
Okay, lots of Conflicting results given here. I believe I have a 235. Would anyone be will to guide me on how I should figure this out. It's a 50-53 5 window chevy 1/2 ton.
Hey guys...I need help identifying this engine...I'm pretty sure it's a 216, but I'm just going off what I can find online and a bore measurement of 3.5 inches that I took. It's a 1953 1 ton and the door tag says it's rated at 85 hp. Thanks!
I think you can just look up the casting numbers, no? http://1954advance-design.com/Stovebolt-engine/casting-numbers.html Sent from my iPhone using H.A.M.B.