Register now to get rid of these ads!

409 Aluminum Block

Discussion in 'The Hokey Ass Message Board' started by NITROFC, Nov 24, 2009.

  1. NITROFC
    Joined: Apr 17, 2001
    Posts: 6,175

    NITROFC
    BANNED

    From ..DRU

    Here are a few snapshots of the brand new World Products aluminum 409 Chevy block on a pallet headed to the upcoming PRI Show in Orlando.

    Not a lot of info on the block yet but a note attached said that Bill Mitchell had 409 guru Lamar Walden do the engineering design and the hope is it is the lightest 409 block ever made.

    [​IMG]

    [​IMG]
     
  2. hummina hummina hummina hummina - woof - imagine an aluminum Lamar Walden built 409 sitting in front of you right before you dropped the clutch! yeeeee frickin ha!
     
  3. panhead_pete
    Joined: Feb 22, 2006
    Posts: 3,487

    panhead_pete
    ALLIANCE MEMBER

    PORN!!!! But in the OEM blocks is the walls between the cyclinders have that little meat?
     
  4. Larry T
    Joined: Nov 24, 2004
    Posts: 7,875

    Larry T
    Member

    Is this the block that is basically a BBC (crank, timing chain, timing cover, etc.) that uses W style heads?
    Larry T
     

  5. Doug Kennedy
    Joined: Nov 17, 2009
    Posts: 28

    Doug Kennedy
    Member


    The reason it looks so thin between the cylinders is,its machined bigger for the O.D of the sleeve flange.
     
    slack likes this.
  6. Candy-Man
    Joined: Mar 21, 2006
    Posts: 1,715

    Candy-Man
    Member

    How many cubes with the BBC crank, rods and pistons?

    I have a 409 with a 454 crank and rods out to 474 cubes......
     
  7. Traditionally speaking these would be great for the drag racers but a cast iron 409 is the real deal, it reflects an era, however change, progress, refinements, upgrades are great and personal choice in a hot rod build keeps us all looking. Thanks to all who take the time, energy, and money to make things like an aluminum 409 available to those who wish to have one.:cool:
     
  8. Candy-Man
    Joined: Mar 21, 2006
    Posts: 1,715

    Candy-Man
    Member

    Well iron 409's may be more traditional, which I certainly agree with, however; I called a company which will remain nameless a short time ago enquiring on the price of a bare 409 iron block. Well for the sum of $5,000 I could pick one up. Needless to say, I just had to laugh at the fellow.... Then the kicker, the bare 348 block could be had for $4,000.... Prices are way out there as some people believe they are sitting on gold. I am curious what the price will be for the new aluminum 409 block?

    I welcome the new block, looks great.
     
    Last edited: Nov 24, 2009
  9. sixpac
    Joined: Dec 15, 2002
    Posts: 553

    sixpac
    Member
    from Courtenay

    There is a 409 iron block in the works as we speack. No word on prices as yet but I think a lower price than the alluminum. There is 409 used blocks around if you look for 1500 to 2500 bucks. For more info on these go to www.348/409.com
     
  10. Larry T
    Joined: Nov 24, 2004
    Posts: 7,875

    Larry T
    Member

    Around here, if you look around, you can get a complete engine for that.
    Larry T
     
  11. sixpac
    Joined: Dec 15, 2002
    Posts: 553

    sixpac
    Member
    from Courtenay

    Hey Larry T that sounds like a good reason to hang around there. Gotta love Texas. If they bring out a new block cast iton reasonable price then the price of the older ones will come down allso. If you want the proper deck codes like QA blocks then not likely.
     
  12. Larry T
    Joined: Nov 24, 2004
    Posts: 7,875

    Larry T
    Member

    No, no QA or QB for that unless you really get lucky. But 409's came in lots of different vehicles. Even some farm equipment used them. And they all work for hotrods.
    Larry T
     
  13. Doug Kennedy
    Joined: Nov 17, 2009
    Posts: 28

    Doug Kennedy
    Member

    Here is a 409 i'm working on
     

    Attached Files:

    • 409.jpg
      409.jpg
      File size:
      146.1 KB
      Views:
      580
  14. impalabuilder
    Joined: Oct 6, 2007
    Posts: 106

    impalabuilder
    Member
    from NJ

    That's Bob Walla Racing
    http://www.409raceparts.com/

    He's planning on putting out iron blocks but mostly aluminum. Here's the progress, some people believe that he will have the first available closest to genuine 409 block. It will accept a 454 crankshaft if I'm not mistaken

    progress:
    http://www.348-409.com/forum/showthread.php?t=13128

    and:
    http://www.348-409.com/forum/showthread.php?t=16425

    I don't know much about these in the pictures other than if you ask about them, you don't get an answer, according to posts at 348-409.com
     
  15. Yes. It's essentially a BBC that's been modified to match the W-engine's angled deck. Not really a "409" block, IMHO.

    If I'm not mistaken, the Bob Walla Racing (BWR) blocks will be visually identical to the OE blocks. I'll be buying one of Bob's blocks before I buy a Walden/World block; just like how I purchased a pair of Bob's heads over a pair of Edelbrock's. Support the little guy who's in it for the love of the engine instead of making $$$.
     
  16. Lamar Walden is the man that is in it for the love of the engine. If you've ever met the man or have seen his operation you'd understand that. He been racing all his life with 409s and knows them inside and out. He is a great guy. I bet a 10 minute converstation about what went into the deisgn of that block would blow you away. I bet he put lots of tricks in there to improve the original design. Every time I am over there he'll tell you a story or teach you something when you go buy the mill machine or one of the blocks he's working on. I love stopping by there.
     
    Last edited: Nov 24, 2009
  17. Terry O
    Joined: Oct 12, 2004
    Posts: 1,060

    Terry O
    Member

    .....billet.

    Terry
     
  18. Larry T
    Joined: Nov 24, 2004
    Posts: 7,875

    Larry T
    Member

    No, cast. Unless you're using newspeak.
    Larry T
     
  19. Kan Kustom
    Joined: Jul 20, 2009
    Posts: 2,739

    Kan Kustom
    Member

    I like You !!!!!!!
     
  20. yellow wagon
    Joined: Jun 13, 2007
    Posts: 612

    yellow wagon
    Member
    from WI

    [borat]She's a nice!![/borat]
     
  21. Brad54
    Joined: Apr 15, 2004
    Posts: 6,021

    Brad54
    Member
    from Atl Ga

    Well, I guess I'll weigh in. Other than Lamar, his son Rob, and possibly Bill Mitchell, I probably know more about these blocks than anyone in the country. Actually, I probably know more than Mitchell because he doesn't know that much about the original blocks and their shortcomings.

    I was at Lamar's when he was prototyping the first one on his CNC machine, and I did the story on them that's in Super Chevy (last month or this month... don't know).
    Passenger car 409 blocks start at $3,000, and that's a deal. Truck 409 blocks aren't far behind. I have yet to see a complete 409, (truck, passenger car or irrigation pump) for less than $2,000--and the heads, intake and water pump are throw-aways. Lots of blocks are worn out, need sleeves or a really big overbore. Complete 348 are still a dime a dozen... and just like every early Hemi is "a 392," every W-motor is a 409, even if it's not.

    All 348/409 blocks have a few weaknesses: run them too hot, or get them too cold, and the block cracks below the deck from the middle of the front cylinder all the way to the middle of the rear cylinder. That area is too thin.
    They are also weak between the lifter galleys.
    Lamar addressed this, plus he put a thicker deck in it for strength, so the head bolts won't pull out in boosted or sprayed engines.

    Pan Rail: It's the same pan rail as a BBC... prices for original 348 and 409 pans got a little silly for a long while. There are repops available, but they're still expensive. And other than a Stef's pan, you're SOL if you want a deep sump, a road race pan, or a pan with kick-outs. In other words, now you can call Milodon or Moroso and get a decent pan, rather than an expensive stock repro or a piece of rusted, dented original shit that needs to be restored.

    Timing chain cover: Again, 348/409 covers are unique, and expensive. There are also different covers for the different sized dampers (placement of the timing tab). I don't know if anyone is making reprops of those. Rusted, pitted and dented original, or pay a lot for a nice one. OR now, get any number of modern covers, including finned aluminum.

    Water Pump: it's as big a visual cue as the valve covers--Lamar kept it, rather than a BBC pump.

    Cams: 348 and 409 have BBC cam length, and SBC cam bearing sizes. It's a unique core. Guess who was the only source in the country for 409 cores? Crane. The supply all but dried up last year--Lamar got the last couple from COMP (incidentally, Lamar was the very first racer to run a Competition Cams sticker and cam in his race car... he goes back with them to the beginning). Lamar has a guy supplying him now, but with BBC cams, the options and supplies are wide open. Also, with a larger cam bearings, you can put higher lift lobes on it. Someone tell me how that's a bad thing?

    Lamar didn't give me a price on the blocks, but he's shooting to have them available for about the same money as a prepped iron block can be had...

    So for all you "trad" doofs, these blocks weigh less, will support more CI (509 stock, 609 possible), are lighter, are stronger, will use better and more readily available parts, and every one in a race car or hot rod is an iron block that can go back to a resto car. So it's made out of aluminum... big fucking deal. So's that old Tattersfield or Edmunds intake. What about new cast iron Fenton headers? They're repops too, but they get a pass because a magnet sticks to them?
    Paint the block if the sight of cast aluminum bothers you.

    Incidentally, I've spoken with Bob Walla a couple times. Nice enough guy, but... there's a reason I go to Lamar's.
    Lamar's first race car was 409 powered, and he ran a blown/injected '09 in a '33 Willys gasser back in the early '60s. Eventually, he took delivery of the 51st ZL1 '69 Camaro, directly from Vince Piggins, and raced it in Pro Stock. He's been Chevy his whole live, and he's done more with the 409 than anyone on the planet, and he's done more for the 409 than all the other guys out there have TALKED about doing.

    -Brad
     
    Tickety Boo likes this.
  22. Brad54
    Joined: Apr 15, 2004
    Posts: 6,021

    Brad54
    Member
    from Atl Ga

    It also occurs to me that the things that make a 409 mechanically unique are the port design and layout, the valve arrangement, and the fact that it's a flat head with the combustion chamber in the block. Visually, the heads, valve covers and water pump are what really sets it apart.
    Sneering at the pan rail, timing chain cover, cam journals, etc. is really pretty dumb.

    I wonder how these same guys feel about the French flat heads, Donovan hemi blocks or Bob Walker's aluminum hemi heads... after all, they're not the "Trad Triple Nickel" heads.

    -Brad
     
  23. well I dont see an issue here. I welcome the new one.. can't wait!
     
  24. yellow wagon
    Joined: Jun 13, 2007
    Posts: 612

    yellow wagon
    Member
    from WI

    new technology is a good thing. It helps advance our hobby! We all benefit from that!
     
  25. Larry T
    Joined: Nov 24, 2004
    Posts: 7,875

    Larry T
    Member

    I've run into the same kind of thinking on new Harley "Panhead" engines. Some folks think that if you don't use the original stuff it's a fake. That's not really a problem for me unless you're working with an original, numbers matching vehicle. But hey, I've got nothing against aftermarket hot rod bodies (steel or fiberglass) either.
    As far as Edelbrock vs. BWR vs. Lamar Walden, in the end they all have to make a profit or they won't be around very long. So do your research, figure out which products work best for your application and get after it!
    Larry T
     
  26. chaos10meter
    Joined: Feb 21, 2007
    Posts: 2,191

    chaos10meter
    Member
    from PA.

  27. sixpac
    Joined: Dec 15, 2002
    Posts: 553

    sixpac
    Member
    from Courtenay

    Thank you BRAD54
    very informative. I like to add allso I love the sound of the 348 I am running. Nice deep voice. They hear me coming 2 blocks away
    My avatar is my new intake
     
  28. Jeff Norwell
    Joined: Aug 20, 2003
    Posts: 14,809

    Jeff Norwell
    MODERATOR
    Staff Member

    I sure wish someone would cast a 392.....
     
  29. Brad54
    Joined: Apr 15, 2004
    Posts: 6,021

    Brad54
    Member
    from Atl Ga

    The only problem I see with that intake is your avatar is that the picture isn't nearly big enough! Come on man, post up a big one! I'd love to see it!!!

    I'm currently lusting after a stroked 348 with Edelbrock heads for my '62 Suburban. I'd freakin' love to have that thing in there... all painted and hidden like it came that way from the factory.

    -Brad
     

Share This Page

Register now to get rid of these ads!

Archive

Copyright © 1995-2021 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.