The Jalopy Journal

AV8 Dave · 07-03-2004, 02:03 AM

Hi Everyone! Fired up the digicam tonite and flashed some more detail pics of my recent work. First up is one view of the pedals. I had to make up a 1/8" plate to help locate the pedals in their new location. It's between the pedal mount flange and the crossmember:

AV8 Dave · 07-03-2004, 02:05 AM

View from the front top side:

AV8 Dave · 07-03-2004, 02:08 AM

Next up is the clutch linkage. The little block that holds the ball joint is a solid steel chunk I had that I used with my 12 ton press. Fit perfectly!:

AV8 Dave · 07-03-2004, 02:13 AM

DOH! Almost forgot this one - a top view of the pedals. You can see the section I had to shave off the leading edge of the stock "A" crossmember to be able to slide the master cylinder in:

AV8 Dave · 07-03-2004, 02:18 AM

And finally, here's one for you Southfork:

**HotRodMicky** · 07-03-2004, 04:16 AM

Hi Dave,
did you have to the pedals, because they wouldn't clear the rails?
Is the front motor mount in level with the top of the chassis?
Good looking chassis that you are building there,
Michael

07-03-2004, 02:03 AM	#1
AV8 Dave Grenade Inspector Join Date: Jan 2003 Location: Victoria, B.C. Canada Posts: 388	CHASSIS, More AV8 - F1 crossmember Hi Everyone! Fired up the digicam tonite and flashed some more detail pics of my recent work. First up is one view of the pedals. I had to make up a 1/8" plate to help locate the pedals in their new location. It's between the pedal mount flange and the crossmember: Attached Thumbnails

07-03-2004, 02:05 AM	#2
AV8 Dave Grenade Inspector Join Date: Jan 2003 Location: Victoria, B.C. Canada Posts: 388	Re: More AV8 pics for Matt, Southfork, et al.......... View from the front top side: Attached Thumbnails

07-03-2004, 02:08 AM	#3
AV8 Dave Grenade Inspector Join Date: Jan 2003 Location: Victoria, B.C. Canada Posts: 388	Re: More AV8 pics for Matt, Southfork, et al.......... Next up is the clutch linkage. The little block that holds the ball joint is a solid steel chunk I had that I used with my 12 ton press. Fit perfectly!: Attached Thumbnails

07-03-2004, 02:13 AM	#4
AV8 Dave Grenade Inspector Join Date: Jan 2003 Location: Victoria, B.C. Canada Posts: 388	Re: More AV8 pics for Matt, Southfork, et al.......... DOH! Almost forgot this one - a top view of the pedals. You can see the section I had to shave off the leading edge of the stock "A" crossmember to be able to slide the master cylinder in: Attached Thumbnails

07-03-2004, 02:18 AM	#5
AV8 Dave Grenade Inspector Join Date: Jan 2003 Location: Victoria, B.C. Canada Posts: 388	Re: More AV8 pics for Matt, Southfork, et al.......... And finally, here's one for you Southfork: Attached Thumbnails

07-03-2004, 04:16 AM	#6
HotRodMicky Alliance Member Join Date: Oct 2001 Location: Buende , Germany Posts: 1,384	Re: More AV8 pics for Matt, Southfork, et al.......... Hi Dave, did you have to the pedals, because they wouldn't clear the rails? Is the front motor mount in level with the top of the chassis? Good looking chassis that you are building there, Michael

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode