The Jalopy Journal
For '67 - '84 318 New .040 over cast EngineTech 1516-8-040 flat top pistons with used rods. Brand new pistons, no rings. One rod cap missing....
[ATTACH]
I'm sure a couple dozen of you know what year and model this is from. I don't, but would like to know. Thanks! [ATTACH] [ATTACH]
I'd like to know if a 1960 RotoHydramatic (Slim Jim) transmission will bolt up to a 1964 Olds 394. I'm unfamiliar with the bolt patterns, but do...
Hey folks, I'm going to go to the showing of American Graffiti on the big screen, 4PM at the AMC Studio 28 Theater, August 27th at 4PM. If some of...
Even the safety measures in the late 50's saved lives. [MEDIA][/QUOTE]
I need to purchase a radiator for a '31 Model A. Cadillac flathead (same basic inlet and outlet locations as SBC/BBC/whatever. The three I...
I need to confirm that this rebuilt starter is wired correctly. Most of these connections, including the start relay, are within the starter...
I'm currently working on a Cadillac flathead powered Model A, and somewhere in the annals of the HAMB was posted an analog two-needle electric...
EDIT: OOPS! I did a search AFTER I posted this and found pretty much all the info I needed. I have a Model A axle that is in very good condition...
I've done some searching and haven't been able to find this casting mark on any of the SBC Head ID charts. Seller hasn't responded with any head...
A couple weeks ago I started a thread about the broken latch springs in my Model A, and where I might be able to get replacements. I was able to...
Do any of you have a source for the door latch springs and window regulator springs, 1931 Model A Coupe? I have contacted a few of the Model A...
I'm getting ready to replace a badly rotted header in a '31 Model A Coupe, and was wondering if it would be a good idea to seal the new...
Pick this up for a buck at a swap. Do any of you know a source for rebuild kits for these old pumps? This one is all good except for the diaphragm...
I stole this photo from another thread. What years were these rear wishbones used? They look like something I could use on a project I'm in the...
I was cleaning and tapering the front spring pack on the '31 Model A I'm building, and saw this logo on the bottom of the second to top spring....
I recently bought a Model A front axle and brakes from a fellow who decided to go a different direction with his build. I don't know what all of...
I am in the midst of tearing the wood and such out of a '31 Ford Coupe, and replacing the body framework with metal. Decades ago a previous owner...
I need to replace the rear half of the subframe in a '31 Model A Coupe, and was wondering if someone on the board could take the time to get a...
Looks like the Ford crapped out, so they added a Cadillac with a Hydra-Matic in front of it. How did they keep the Ford crank oiled? [ATTACH]...
I'm in the midst of building a Model A, Flathead Cadillac powered with a '37 LaSalle trans behind it. The clutch disk I have is worn, and instead...
I was in Detroit last week, and since my wife was along we had to stop at one of those antique malls. I normally resist these kinds of excursions,...
I am in the process of collecting parts for a '31 Model A Coupe, and was wondering if the reuse of good condition stock front springs, hangers and...
I'm stripping off the extra bits from a 1928 Model A frame and would like to know what these are. They're located on the frame towards the rear,...
https://www.enginebuildermag.com/2009/04/flat-or-tapered-cams-and-flat-or-crowned-lifters/
I have been chatting on another site regarding the purpose of the residual valve for drum brakes. All over the internet are descriptions that say...
I was kicked back this evening having a Mohito diluted with a bit of cranberry, and dropped into an Ed Roth internet rabbit hole. I got to...
Sale Pending. For sale is a freshly re-gasketed 1931 Ford Model A motor and transmission, sitting in a partial frame. Take or leave the frame,...
I'm sorting through boxes of stuff I've had ratholed in the back of the shop forever, and found these spindles which I don't recall the origin of....
Separate names with a comma.