The Jalopy Journal
I have a very clean and straight 1935 Ford Truck Grill shell for sale. Asking $1,050. I would prefer local pick up but if you need this, we could...
Does anyone need a RV site for Speed Week? I have an extra site for Friday check in and Monday check out (8/4 thru 8/7). I had it reserved for our...
1941 Lincoln Zephyr front windshield, a pillars, interior/exterior trim and cowl vent assembly. in good shape. Asking $275 obo [ATTACH] [ATTACH]...
1941 Linoln Zephyr rear window assembly. Rear glass, interior trim pieces and the whole window opening asking $250 obo Matt [ATTACH] [ATTACH]
1941 Lincoln Zephyr Hood for swale. No rust, very straight. The chrome strip down the middle is bent up. Asking $350 obo. Thanks! Matt...
I am listing my 1958 Edsel Ranger for sale. The car has 55,000 miles +/-. I purchased the car from the second owner who lived in Washington state....
My son and I are building his 1950 Chevy 2 door fast back. We are putting a SBC, 700r4 and 1955 Chevy car rear end. We want to lower the car 3"....
My son Eli and I will be building this car together as a father son project. Eli is 12 so we have about 4 years to get this thing done. We will...
I have a 1958 Edsel that I need some electrical help with. The car ran fine and then I had some electrical issues. I need to either re-wire the...
I have a 31 Chevy 2 door sedan that I am building (build thread to come at some point). I have the front suspension bolted in and now need to...
I need to be in San Francisco the week of 10/21 for work. I have my Edsel sitting at my parents house. I am thinking about renting a trailer and...
Let's get a thread going with hot rods running four springs. I will get it started with this 31 Chevy roadster. I am building a 31 2 door sedan...
Sun tach model FZ-108N tach with 10k range. From what I have read, this model does not require the transmitter. I have not had this hooked up so...
1956 Oldsmobile dash, speedometer, clock and dash controls. They came out of a running car when pulled 15 years ago. Asking $400 shipped in the...
I have an early SBC factory 4 barrel intake in great shape. Casting #3866922 shows it as a 220/250 hp 283 or 327. Asking $120 local Austin area...
I have a Cal Custom 40-40 aircleaner for sale. In good shape with patina for ths into that or polish it and run it. Asking $100 shipped to US...
I have a set of Cal Custom 40-2000 valve covers for a small block Chevy that are straight accross bolt pattern...not staggered. Lots of great...
Does anyone have recommendations for a steel supply and welding supply in Austin/Dripping Springs area? I am about to start a 31 Chevy build and...
Anybody out there have a 1929-31 Chevy Hot Rod? Anybody out there in the middle of 1929-31 Chevy build? I am about to start on my 1931 Chevy...
Does anyone know the cost to have a car hauled from San Francisco bay area to Houston Texas area? I have two cars that would need to go and I am...
I have a nice set of 1929 Chevy front and rear fenders for sale. They came off of a 2 door sedan. I will post pictures later. The fenders are very...
Anybody build or in the process of building a 1929 Chevy 2 door? Let's see them. I have been collecting parts for the past year for my next hot...
So I have about 6 gallons of gas in the tank of my Edsel that has been sitting for two years. Just about have it road ready again and am wondering...
So I have a 58 Edsel that I have been working on for the past two years. Not as much time as I would like to spend but we all know how that goes....
I need some help from you Ford guys. I have a 58 Edsel with a 3 speed auto. I just finished rebuilding the engine and was installing the speedo...
Come on out to Emil Villas for some breakfast and old car fellowship. 7:30am at Emil Villas in Livermore. We get together the last Sat of the month.
So I have my engine and trans out of the Edsel to put a new oil pump, seals, freeze plugs, water pump and transmission seals. My question is...
This will be our 4th get together. We have had about 20-30 the people the past 3 times. Come on out!! Where: Emil Villas Hickory Pit 3064...
So I have a 58 Edsel Ranger with a 361 and Auto trans with 54,000 miles on it. When I got the car the tranny leaked ALOT!! I pulled the gear box...
I was driving my 58 Edsel the other day and I noticed that the oil pressure was now at 1 or 2 pounds at idle. Typically the pressure is at 25...
Separate names with a comma.