The Jalopy Journal
They also threw in some front fenders and a light bar. No idea what they are for.[ATTACH] [ATTACH] [ATTACH] [ATTACH]
Yes, some had already chopped it. Not a terrible job, but not great either.[ATTACH] [ATTACH]
Thank you, I did some searching, looks like it's an Erskine Six Sport Coupe?
I am trying to track down what this coupe body is. It has two small glove boxes on either side of the dash. A drip rail. The rear of the body...
Thank you, I wanted to make sure that I wasn't going to bend or break anything that I'm not seeing under there. It acts like there is something...
I'm trying to remove the top cap on a 29 Coupe so we can install glass. I removed the screws on the top of the door, but can't seem to get the...
She has a lot of stock parts still on her.
[ATTACH] Here's the truck I'm working on. Current hurdle, brakes are soaked with grease....
I've searched the web and tried to find by size new front wheel bearing seals for a 34 Dodge Brothers Pickup. I'm having no luck, so I hope...
I tried the aerosol can once, it was a disaster, I only buy it in the caulk gun tubes anymore. I also stash it in the refrig between uses, keeps...
Well, I am running Stromberg 97s which I am told are around 155 cfm each. So when I am running 6 I am around 930 cfm and on just four, 620 cfm....
So true, the only way to do run that kind of hp and get any mpg is run a gm lsx/lq4 motor and 4l60e trans. That's why I never even looked at my...
I can't comment about mpg, I have never really checked it, but our non-stock 400 SBC runs pretty good with the 6x2 we have. I did have to spend...
As I understand it, you need a 56 plate with a 58 tag. The 56 plates have to be clear with the dmv, and the tag you can get off evil bay, or at...
California isn't quite as simple. You have to have a set and get them approved. And it seems the older plates are simpler than the later YOM...
So you can run any older plate you want to run under that law? If so, that is a cool way to do it. I agree with vonpahrkur that running the 29...
"Assuming good traction how much horsepower are ford 35 wires good for" Supposedly, our 400 SBC is running somewhere near 400HP and so far the...
I had the same experience with them. Was told in pretty black and white terms, take your car to the store, parts house, In-N-Out etc. and it's...
Well, found all the parts we needed to get the brakes done, thanks for the Andy source. Now onto the drive line and such... Thanks for the help...
I'm over on squarebirds.org also and yes the guys there are quite bright when it comes to the birds. But looks like you can get a harness...
I haven't experienced that problem, just that on dirt or gravel parking lot at low speed, it will push the front end a bit. Driving it at...
Well, I am running a stock 40 Ford axle and brakes except I have 6.50x16 tires on 35 wires, and I get enough turning radius out of it, but I do...
Wish someone had told my new Firestone front tires that, especially the drivers side tire. The old ones were fine go figure. :mad: Could be the...
Regarding Diamond Back tires and Cokers. We ran a set of Diamond Backs on our TBird, they were awesome tires. The car ran smooth and quiet,...
Here is my brother in laws 34 Dodge project we are currently working on. She is going to be running the full factory steel fenders. Brakes are...
Thanks I appreciate it.
Where did you get the 17" trim rings?
Yes, I'm with you there. I haven't seen problems either.
I used some JB Weld stick putty stuff. I don't remember the name of if, but you cut it off the stick, nead it till it mixes well, and it is...
That's the same wheel I am running, just stock size. I like the leather wrap though, that's very cool. [IMG] [IMG]
Separate names with a comma.