The Jalopy Journal
Those won't fit I've tried and as for dimensions the Granada style are nearly identical to the 56 other than reaming the lower ball joint hole...
Granada , maverick, comet etc.are all the same69 up mustang and torino too Sent from my SM-G965U using The H.A.M.B. mobile app
I built a 40 ford panel delivery back in the 80s and used a rear wiper motor off of a rear hatchback it was only one speed but it worked great (...
The disk brakes also serve as axle retainers even if a c clip did break or an axle breaks it can't come out because the caliper holds it .i have...
The explorer is stronger and has 31 spline axles and less expensive .to put 9-inch ends on you will need custom made axles too and that defeats...
It doesn't take very much to get it down to the correct size either .i left the flange for the ujoint and got an aluminum drive shaft from an 06...
I flew on a 1929 ford Tri-Motor airplane a few years ago and believe it or not it had Disc brakes . Sent from my SM-G965U using The H.A.M.B....
Well look at all the 350s in these cars too Sent from my SM-G965U using The H.A.M.B. mobile app
The way i did it is i cut the tube in the flat area just before it goes to the 31/4 diameter then again after it flattened out the smaller...
Get a 95 -01 explorer or mountaineer rear end and shorten left tube and use another right side axle .i have one under my parklane .3:73 post with...
My first race engine (oval track) was a 69 351 W I ran it mostly stock lower end .i spent time cleaning up the exhaust ports, and screw in studs...
I never did mine when I was racing and never had a problem .of course later on in the higher classes we ran full floaters Sent from my SM-G965U...
Circle track guys did that a lot to prevent the left side working out , personally, I never had that issue.if they are put on correctly they don't...
Car part machine fixed some machine work I had done in las cruces once on a race engine had to rebalance rebore and put in new pistons due to...
Not me I never take anything personal and yes we all have different tastes and flex hoses aren't one of mine .i don't care what anyone else uses...
I personally don't like ribbed hoses to me they look generic like one size fits all .but that's just my opinion and as we all know opinions are...
Mine have been awesome .its on cast iron manifolds but in a year they look like the day I did them .it doesn't take much either to do 2 manifolds...
I like cerakote Sent from my SM-G965U using The H.A.M.B. mobile app
Dam mine just has tri power Sent from my SM-G965U using The H.A.M.B. mobile app
Dam that was a funny movie Sent from my SM-G965U using The H.A.M.B. mobile app
The grill reminds me of the aftermarket tube grill for a 59 chevy .when I was 16 I built a 49 ford coupe and had no grill I took one of those tube...
Point of aod is to have both lower gears for acceleration and to have the overdrive for cruising the C4 doesn't have that Sent from my SM-G965U...
I like it Sent from my SM-G965U using The H.A.M.B. mobile app
Or if you want both change out the c6 for an aod and put 3:73 or so gears in the rear Sent from my SM-G965U using The H.A.M.B. mobile app
I run mobile1 in everything 10w30 Sent from my SM-G965U using The H.A.M.B. mobile app
What I did on mine to make sure I don't ever have an oiling problem is I cut a 1/16 inch wide groove a 1/16 inch deep between the oil feed holes...
Your welcome Sent from my SM-G965U using The H.A.M.B. mobile app
Yes Sent from my SM-G965U using The H.A.M.B. mobile app
Dennis carpenter has both upper and lowers complete with fomoco lettering Rock auto has molded without the logos for less money[ATTACH] Sent from...
My 56 ford came with molded hoses so I guess that makes molded hoses traditional Sent from my SM-G965U using The H.A.M.B. mobile app
Separate names with a comma.