The Jalopy Journal
Car has been sold.
BTT
Spring time...time for a new project.....:) Asking $5000 US , or $6500 cnd...OBO! As above open to trades of snowmobile, or quads, or 1980-1993...
Still have this car kicking around. Would like to see it gone.....;) Asking $5000 US , or $6800 cnd...OBO! As above open to trades of...
Still have this car kicking around. Would like to see it gone.....;) Asking $5200 US , or $7000 cnd...OBO! As above open to trades of...
BTT.... Asking $7500 Cnd , or $6000 US , or OBO.....or open to trades on 600cc snowmobiles. Would like two sleds, pre 2011. Or perhaps a nice...
BTT.... Asking $7900 Cnd , or $6350 US , or OBO.....or open to trades on 600cc snowmobiles. Would like two sleds, pre 2011. Or perhaps a nice...
BTT.... Asking $8500 Cnd OBO.....or open to trades on 600cc snowmobiles. Would like two sleds, pre 2011. Lets work out a deal. ;)
Asking $9000 Cnd OBO.....or open to trades on 600cc snowmobiles. Would like two sleds, pre 2011. Lets work out a deal. ;)
Bump...:)
1948 Desoto 2dr Sedan, Very good condition for it's age, original patina paint, Little bit of rust through in trunk spare tire well, and near a...
And I installed all new gauges in the OEM dash...except the speedo. I used Auto meter (Autogage) units, these were your typical 2"-ish gauges. I...
And I had to hook up a couple jump wires to see the car with the lights on! [IMG] [IMG]
Once the main wiring harness was through the firewall I had to sort it all out. Three bundles....Front end lights, turn signals etc, then engine...
Back end all finished off.... [IMG] [IMG] [IMG] the green wire is for the reverse lights. I have not installed them yet, and might not since...
Well haven't been updating on Fernando regularly...just too many projects, on too many vehicles etc. So here is an update from the last few...
Then it was onto the forward harness. I was shocked when the wiring fit within the factory firewall grommet and bracket! [IMG] Again I think it...
Then get it sorted a little better and fed down through the package tray area and into the trunk. [IMG] The old rear harness... [IMG] And the...
I first mounted up the fuse box, then tried to tie the new wiring to the old wires to drag them up through the pillar post on the drivers side....
So I started stringing the wiring through out the Desoto the last few days. First I had to sort it and wrap it. I like to use hockey tape to wrap...
Then once I knew the fuse box panel was fine I had to get it mounted up in the car. Couple holes, build one small upper bracket off the E-brake...
Finally getting off my lazy butt and working on the Desoto. I am working on the 12V conversion wiring system, but needed to find a place to mount...
Thank you for this great info and link....just what I have been searching for!
Sucks about your T....but this statement about Karma....Might be some truth to it???
I just worked my way through this entire thread...I'm speechless at the dedication you have shown to bring this poor old Willys back from the...
Dragging this one back to the top. Just got Fernando home after a year or more in hibernation. [IMG] [IMG] Will be trying to re-wire the...
Thank you! Slow road but getting there.;)
And now a video of me driving up and down the street...with the new tires. What a difference having 4 new tires makes!! [IMG]
And now Fernando outside with it's new Coker 7.60x15 Bias Ply wide whites..... [IMG] [IMG] [IMG] [IMG]
Then it was time to re-assemble the dash...again in a rush and didn't grab assembly pics. But here it is all back together and in the car....
Separate names with a comma.
The Jalopy Journal
