The Jalopy Journal
Not too sure how easy of a swap it would be with the computer control on the ignition and fuel system, if he can figure out how to wire that mess...
Yeah frigen thieves suck, that dirtbag probably took it to a local recycler and got some crack money out of it....around here they been using a...
not technically Michigan, I am as far north in Ohio as you can go, 30 feet from my back door is the oh/mich line....I know Danimal, bought from...
You sure that thing was never used??? I see a couple Orbs in the pic HMMMMMMMMMM!!!!!
try here, I bought all my lower body panels from these guys....The fit isn't exact but they dont look bad, a little tweaking here and there,...
Thanks Guys for the info.....After reading your replys I just bought an inexpensive mustang short thow of e bay with the shifter stops...it's...
a friend of mine had a 6 pack intake for one of those, I had it for a while in my attic and gave it back to him some time later, found out shortly...
I can't even begin to imagine the amount of work that went into that or what it would be worth if he sold it...That is just too amazing to...
definately not the right body for lace, lace belongs on 60's flat body cars or the front room window..
Thanks for the replys...I plan on using a 403 bellhousing so I can run the trans straight up and not on an angle like the stock camaro set up...
I have used it a quite a few times and have had good success with it.... I usually sprayed it fairly thick yet wet, it fills nice and sands out...
as a 19 year old in the early 80's I had a 64 Dodge Polara 383-4 speed that was named after the AC DC tune "Night Prowler" which was painted...
I searched prior T5 posts but didnt see anything regarding this question...Will a mustang T5 shifter fit on a camaro T5??....the reason I thought...
I believe it's a 1930 model 66B coupe
Duece, any chances of getting more shots of your 40?? Randi
I did this with an 89 h.o 302 in my son's Ranger, I used a one wire HEI dist, I also switched the roller cam for a flat tappet cam..... This the...
that is one beautiful car, you captured the look just perfect with the color, wheels and tires...I wouldn't change a thing......Very nicely done....
not for a lack of inginutity but what a waste of a sweet engine....I'd rather see that in a gasser, salt flat racer or 30's coupe of some kind but...
Not sure what engine your what engine your buddy is talking about but there was a Police engine (283) that had small counter balances on the...
angle the post, the roofline is wrong for a hard top and a straight post just takes away from the looks of the chop...I think an angled post would...
Thanks everyone for all the help and info, you have given me a lot of ideas on what to look for to set this up.. I have to get some measurements...
I believe in 98 or so they also went with a Hyd throwout bearing, I'd rather stay with a slave cylinder in the event of failure it will be easier...
The stock line does not have threaded ends like brake lines, the ends have O-rings and a roll pin to hold them in place...The hose is a moled...
Does anyone know if there is any difference as far as pressure requirements of different style hyd master cylinders for GM clutch set ups?? I am...
what about making some sort of heat shield that would mount to the header flange?? 2.5" from the header is not a lot of space, going down the road...
what about a Mopar ballest resistor??....
try setting your camera on a smaller image size.....If you have windows paint you can resize the pics by opening the pics with paint, go to...
I am looking at an S-10 T5 this evening or tommarow for parts (4.3 bellhousing, top plate and tailhousing) and would like to know if there are any...
will the car pull in 2nd or 1st?? I had a 400 years ago with a B&M kit, when it got hot it would drop to low by itself and wouldn't work right...
did you try jumping the solenoid to see if it will crank over??....there should be a fusable link at the solenoid, make sure that isnt burnt.....
Separate names with a comma.