The Jalopy Journal
My Buddies 49 coupe. He lives here in Hurst, Texas and the car was only driven 20 miles after the complete build 1995. He is selling it due to bad...
I did not see this till today. I have a Littlefield that he built for my 32. Great guy to deal with and a great loss to Motorsports. God's...
After reading most of the thread two are more times it is great to see all these 49-52's in one spot so to speak. Yes, there is some that make you...
I think he is want to change a set of unilug wheels to single pattern. Post a picture of the wheel and state the material the wheel is...
Cool, glad it's back on the road. The picture of Silva and Reggie is pure 50's...... We don't need No Dang Fender Covers !! LOL
Congrats Big Cheese, glad you got That.I was hoping someone on this thread would get it. I was watching it and the price was right..... I just...
Personally I think that is great choice for a dash and it will compliment the car. However, with out being there to see what is actually happen, I...
My wife and I tripped around the country 69 thru the mid 70's in my 35' Chevy coupe pulling a pop-up camping trailer and we stopped at that...
Yes on the front,but the 71-72 rear brakes were still drums..... the same shoes and adjuster kits.
The brake adjuster kit for 65-72 DRUM brake 1/2 ton Chevy pickups will work fine.There will be a left and right kit but it is they are the same...
Just about all the major Hot Rod cam Manufactures make adjustable push rods in any length you want and many different tip configurations. This is...
Thanks Groucho for bringing up a good point.I was considering shaving the door handles on my '50 but I am definetly going to keep the door...
Added note: As general rule new lifters on a used cam is ok... used lifters on any cam other than the cam they were run on,in the exact postion is...
After doing some more research the 3896929 300 Hp 327 cam had a casting number of 6930 in some cases. It can probably be assmed this is not the...
I am not sure and could be wrong but, I think the cam you have is a L-48 295 hp 350cid (3896930) not the 350 hp 327cid cam(3863151/152)....
I to recall seening a picture of this car and definetly recall its odd top shape. I have wondered if its odd styling was due to the fact the car...
BlackRat explained better than I did. Man I need to get up to Mckinney and see the Black Rat
Cant resist it Todd but if it ain't broke ... don't fix it ! LOL
You also will damage the locking feature of the nut so you will need to install a new nut or stake it with a punch. The thread deal might be a...
What Quad Quad said about the drag is partially correct but that can only be measured when the ring gear is out of the case and with an INCH...
You do not need a puller. The pinion should side off with a little persuasion of a soft Hammer. It will be splined. Beware that when you break the...
16 is good vacumn but that is the total of 8 cylinders so you need to have a way to isolate the bad cylinder and see what it is actually doing....
It sounds like a vacumn leak on that port runner. The best way to confirm that is get the motor to some one who has a engine anylizer that will...
what good reason to have a backache. LOL
I think you would be using a stud in this case. I have re-threaded plenty of grade 8 Bolts but you if you where really peticular you could have...
I agree with you, I personally think using a rolled thread bolt/stud is stronger and helicoils installed properly are great. Just thought I would...
Just for the record for you guys that either don't have a lathe that you can cut threads on or if you just don't want to fool with it ,here is a...
Yep ! What they said ! Always nice putting a face with a Handle. Thanks Big Tony.
Prayers on the way ....you have put your trust i the right place .... God knows what is wrong ... he will take care of him.
Go to this link and read this . I may have told you wrong since it depends on the type of generator you have. I normally mess with GM and Chrysler...
Separate names with a comma.