The Jalopy Journal
I have always admired the seats built by frank wallic. Does any one know how to get in touch with him or know what he charges? I tried searching...
i bought these backing plates and drums second hand. every thing looks good but when you tighten down on the spindle nut the drum rubs the backing...
[IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG]
the church down the road is putting on there 3rd annual car show. there were a few hambers out there last year. it was good time for a good cause....
is there any reason why you cant use a set of shocks off the front of a early 40s car on the rear of my model a?
can you run a generator with a 12v system or do you have to go to a alternator?
is there a difference in the 39-45 backing plate from the 46-48? or is it just the shoes and drums? and how do you i.d. the different year backing...
does any one sell the drive shaft coupler that goes from 6 splines to 10? for puting a 46 torque tube shaft on a 36 rear. any help will be...
im looking for a torque tube clamp,coupler piece. does any one sell them and what is the correct term for this piece? i have the piece that goes...
does this look like the original wood header? and do they all use wood shims between the windshield frame and header? thanks [IMG] [IMG] [IMG]...
there's going to be a show at the otis rd. church of god on march 6 from 11am to 2pm registration fee$25 trophy's awarded in 3 different...
what is a good clearance for rear axle travel from rear end housing to the bottom of the floor? how many inch's of travel will i need? 2? 3? 4?
i was thinking of running a aluminum floor maybe 16 ga. with lots of bracing.will this work? anybody done it and what are the pros and cons?
how much brake pedal travel should i need ? im running manual drum brakes all the way around. i have a 6:1 pedal ratio with a maximum amount of 6...
can some one give me a measurement on how tall they are from where it sits on the block to the top. i like the looks of them but don't know about...
how many cfm is a holley 94 EAB ? i did a search but couldnt find any on the EAB
i need a measurement where the rear deck lid starts its curve down i need to know how wide is the gap between the two quarter panels are. i dont...
[IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG]
just want to let every one know that there's a car show at the otis rd. church of god march 7th from 12noon till 5pm. they will also have slot car...
I'm really torn on weather to louver my deck lid.i bought a sheet of Steal with louvers in it and i cant decide if want to use it or not.what do...
i want to put a 40 ford dash in my model a coupe and I'm trying to find some pics or threads that might help me out. i did a search but couldn't...
i know that mr schooler died and the shop shut down. but back in the day he was well known as one of the best cam grinders around and had a cool...
can you louver a piece of steel and weld a flat sheet under it to keep the water out? i like the way the louvers in a deck lid look but worry...
well I've been wanting to do this for a while and i finally worked up the balls to cut into it. so here's my first chop. first i taped it up...
i finaly got her rolling. thought i would post a couple of pictures for you guys to see.sorry there not the best pictures .
on the banjo rearends from 35-48 with the spring behind the rear end is the distance from the center of the housing back to the center of the...
do you have to remove all the gold anodize from the new parts in order to paint or can you just paint over it?
i have every thing tacked up but im not sure if the body sitting wright on the frame .does it look OK or does it need something?any opinions will...
is there such a thing as a stromberg 94? i thought a 94 was a holley and strombergs were 48 and 97. im confused.
well i thought i would start a build thread and tell you little bit about my car.i had been looking for a coupe in my price range for a while.i...
Separate names with a comma.