The Jalopy Journal
Pontiac tempest transaxle. That shouldn't be too hard to find. I know that tempest is out there..... but I have never seen one. Yoots drive...
Ever try water based paint? I've used water borne bases from my local art supply and cleared with both Urethane and Lacquer. With candy...
Nice! Frames are basically the same as later models, other than bumper mounts and such. Not a direct fit, but very similar. There are boxed or...
1st, Way cool 2nd, Dual Quad 409 for sure 3rd, Bring it to Thompson Ohio. Two thumbs up!! Sooooo, If I found a covair trans, I could mount a...
Classier with / meaner without... Sunday drive with / Saturday night cruise without
:eek: Wow. Nice! What the "Excalibur" tried to do, but failed....
Nice work. I like the pin up avatar. No shame in offering awesome workmanship for hire. I agree vinyl sucks.....
[IMG] Not the best, but it's mine... keep this post going...
:D eye candy.... http://www.jalopyjournal.com/forum/showthread.php?t=504828 The Caddy in this ford....:eek: :eek:
Cool find, have never seen one in operation. Turbonique had quite a few different product, the drag axles being the most well known. The...
Beautiful, engine eye candy. Like the frame as well, holes are great, and the banjo it super...
:eek::eek::eek::eek::eek::eek::eek::eek:.....The horror, where's the barf bag....:p:D I agree with no white walls after 1960, and I also agree...
I've been trying to decide as well. In my opion the 59 & 60 should lean towards a cruiser wheel rather than a race wheel. The Cragars and the...
Crap you make it look easy:D, I wish.....
Yep, That's a four body trunk on that pig, I know I've had them in there. 6 ft 6" wide so you don't bump their heads.:D .... Don't worry, we...
I think it follows the same rules as chopped tops, instead you're adding. A one inch chop no one would notice, a six inch chop and it looks like...
That was just from the bath? or did you do some scrubbing and wire brushing or something? I'm off to get supplies to start doing this....:eek:
Wow, I am more suprised by her reaction that the fire. Girl did good... Yes, use a ground. It's slim odds that you'll ever have a problem, but...
Is there an "Engine Candy" thread on the go? Don't want to start another, but a search for Beautiful engines isn't turning any thread up. I...
Back in High School I had a VW beach Buggy. Of course it only had the stock 46hp motor. We installed some great big fat tires on wheel adapters...
I haven't had any problems with the sbc I smoothed out in 1994, It's still a dream to keep clean as well. I spent a lot of time grinding that...
I use smooth clean wood as dollys and I have a wood body hammer that I made for the inside from some dowel. I shape it as required for each job....
Inspiring. Awesome chassis work Jules Verne. Totally refreshing to see, no catalogue and credit card involved.
I'd like the "plug" when you're done with it. Fire up my torch and melt some lead. I haven't done that in 20 years. Fiberglass is for surf boards
http://jbweld.net/products/jbweld.php 500 degrees should work. I've actually never used JB weld. Might actually have a use for it now. I...
I did some high pressure pipe today. I made damn sure I didn't stack any nickles!
Didn't know you could powdercoat over filler. That's good to know. Labmetal, and Tiger Drylac. I'll see if I can find some. Thanks. I'll...
I want to smooth out all the casting on the engine block and heads on my engine that I am building. I am looking for a suitable product that can...
Wow! Beautiful engine. Jaw dropping I'm adding old cadillac to my wanted list.
The early 283 motors just had a mounting hub for the pulley. It was just a solid piece, with holes drilled for the pulley. There was no center...
Separate names with a comma.