The Jalopy Journal
what you need is a 206L and a 306L the L means it is a sealed bearing on one side
what you have is a late S10 rear end it is a 8.5 with 28 spline axles for as for the yoke any 8.5 yoke will work with the rite pinion seal i just...
that's a stock ford axle i think the Axel mite be a hare to long and with that cal bracket it is pushing on the bearing instead of just...
All ford small bearing rear housing have the same offset for the axles 2 1/2" it can be a bronco , mavrick ,mustang ,fairlane and it can be 8"...
the new light weight ones that we use dont have that support anymore so i dont see why you can not cut it off and clean it up and use it if you...
all rear wheel cyl are the asme 8.2 8.5 and even 12 bolt they all use 10 inch brakes except 11 inch on wagons that are impala with 5on5 bolt...
thats a 9 bolt out of a jeep or mopar it has some kind of limited slip in it if the cover was off i could tell you for sure if it has c clip...
speedway eng in calif has the rite side bells and stub shafts to do this i have did a few in the past check there web site out . clay >>>>>>>>>>
I had the same problem i ended up cutting the big end off and hot tanking the hole thing a couple of times and a ton of crap came out cleaned it...
what you are doing if you dont ender stand it get a solid spacer kit it has shims and sets up like a dana dont put the front seal in tell you are...
the ones i have always used are gm 49 to 54 pass clay >>>>>>
what you have was called a poor mans posi back in the day they took a 4 pinion open carrier and put the posi block in it with the four springs and...
i have seen this problem before one thing to check is see if the wheel bearing did not come unseated and the lock ring did not slide off a half...
To me it looks like a T90 low and reverse idler for a T90 3 speed trans they used in jeeps studes hudsons and many more but i mite be wrong...
that posi you have has 2 piece side gears and i think the in side ones are not lined up with the out side ones that will give you the 1/2"...
you mite check the rear end you said you were running 5.13 gears and i dont think you have a cooler or pump on the rear end the noise you said...
i sounds to me that the 488 has a posi in it and the side that the axel won't go in the two side gears are not lined up and it wont let the axel...
20 years ago my friend at us gear sent me a print on how to take a 9" traction lock and make it a 8" the left side of the case is the same. the...
if you have a true 61 with a cast iron glide there is a adapter be tween the engine and the trans the adapter has the mounting for the starter if...
55 to 64 chev pass rear ends are not the strongest to be doing that with! Clay >>
what you have there is a dana 44 19 spline the carrer is a 4 ser to put a higher ratio you need a 3 ser carrior for 19 spline only the later 30...
if your bronco is a small bearing housing ? what i have done in the past for my customers to save them money i use the 8" axels and backing plates...
# 1 they are a cast axel the later axels are forged they have a faint heat ring around them where they induction hardened them they are very...
i think you put the center bearing perload sleve i back wards there are three bolts that are tapered that when you tighten them down it pushes the...
my shop does one a month its perty straight forward but truck ring and pinions are completely different than cars take your time and you wont...
now i know where the term bone head came from! Clay >>
i dont know when they started to have titles but i have a 1930 star roadster title that has never been changed from the first owner so i know they...
just look for any ford that has a 9" that has 3/8 holes in the backing plates this has 2& 3/8 back spacing and this should help you. small...
it is a dana 41 still have a few parts left for them Clay
what i do on our cuctomer cars is drill a drill and tap for a 1/8 pipe plug there is plenty of metal to do this use a allen head plug then it...
Separate names with a comma.