The Jalopy Journal
I have a set of Coker Classic Redline Radials. Never mounted, new condition 2 are 225/75R15 2 are 225/75R14 Will ship on your dime [IMG]
I am looking to buy a set of mid-late 60s vintage torq thrust wheels (15x8.5 4 on 4.5 bolt pattern). I want to get some older ones since it seems...
I am running a Holley 650cfm mechanical secondary carb on the 429 ford engine in my 55 f100. Its been on there for a couple of years now and been...
I picked up a set of 14x7 foresight industries drag mags a while back then got a nice deal on some coker redlines (225/70R14). Finally got the...
I have a guy from down under who seems pretty serious about buying my 55 f100. I have never done this before, anyone have any wisdom and or...
It was a nice day yesterday and I happened to have my camera with me so I took some pics of my 55 in its current state [IMG] [IMG] [IMG] [IMG]
Anyone know where (besides from Joe Hunt, those guys irritate me:mad:) I can get a replacement HEI module. It looks like a standard GM unit but...
On my weekly stroll through the local pick and pull, I found a nice low mile (65K) 1961 lincoln that took a hard side hit. After checking it over...
I picked up an RAC tach on epay recently and finally got around to installing it yesterday. It sort of works...it reads higher than the engine...
Got my 55 drivable for the Syracuse Nats last week, its great to be able to move it without pushing....not done but driveable
I am getting ready to have the drive shaft for my 55 f-100 cut to length. I was told by the shop that is going to do the cutting/welding/balancing...
I installed a CPP drop axle (cast ends with a tube in the middle) in my 55 f100, the front wheels appear to be off camber, they are sitting like...
Spent more quality time in the garage this weekend, swapped out the original rear axle for a 9 inch Ford and stuck it on top of the...
Thinking about getting an air board...looking at the Hutchinson 3800, anyone have opinons/advice?
Finally got to spend some time working on my 55. Got the stake pockets fabbed up, tailgate mounted and door buttons from coolhand installed.
I am planning on removing the stock rear end from my 55 f-100, installing a 9 inch and relocating it on top of the springs. I was wondering if I...
I gotta lay some sealer on the concrete pad in front of my garage before winter to try and curtail the road salt eating it away. There are a few...
I was thinking about maybe taking a little height out of the roof of my 55 f-100 but didn't want to chop it. Any thoughts or opinions on the idea?
here are some better pics of my 55 with the drop axle installed...the tires are taller than what it'll have when finished by about 1.5-2 inches...
I am going to be making a road trip this weekend....any good yards near roanoake VA that would be worth checking out???
finally carved out some time int the garage and got the 2nd Kaiser tail light and gas tank filler installed....whatcha think? still got some...
I found this pic in a thread a while ago an dig the split bumper look and am thinking of doing something similar on my f-100 anyone able to tell...
I am thinking of heading out there to look at a used Jeep at crestmont chrysler Jeep (its a 1998 grand cherokee, low miles) but it'll be a 5 hour...
I am considering shaving the door handles on my 55 f-100 and was wondering if anyone could reccomend some decent quality door poppers and any...
well, I have been relatively sucessful at my first attempt at recessing 49 Kaiser tail lights into the rear fenders of my 55 F-100, well one...
I am refitting a 55 Pontiac with a factory power brake setup. Here is the question...Where do I mount the reserve vacuum canister?
I picked up a set of these rims cheap, they are steel with a side ring? They have both ford and Kelsey Hayes Part numbers .the Kelsey Hayes...
It was a good weekend for the truck...painted the firewall/bottom of the cab, finished cleaning/painting the engine/trans and dropped the whole...
I am going to be installing an early 70's 429 in my 55 f-100, I purchased an engine x-member from Mid-fifty ford parts and am trying to figure out...
Hey folks....heres the intro kind of new to the hot rod scene, Mostly been into mid sixties and up projects until last year, bought at 46 hudson...
Separate names with a comma.
The Jalopy Journal
