The Jalopy Journal
I HAVE A COMPLETE SET OF MOLDS TO REPRODUCE / MAKE MID 1960,S LOGGHE BROTHERS #4 ENCLOSED CHUTE DRAGSTER BODYS. THERE ORIGINALLY MADE BY AL...
I,VE GOT A REAL 1960,S AIR SCOOP UNSED ON UPRIGHT FUEL INJECTORS OR 1 IR 2 4BBL CARBS AND UP TO 4 STROMBERG STYLE CARBS. ITS N.O.S. NEVER CUT ,...
his shop sure does excellent work. from my experience. i know he moved.
I,VE GOT A BRAND NEW SBC CRANK AND ROD OIL SCRAPER 4 SALE. CALL FOR DETAILS. WORKS GREAT. I PUT THEM ON ALL MY ENGINE BUILDS. MADE FROM 18 GAUGE...
SEEMS LIKE A LOT OF GUYS HAVE OPINIONS OR KNOW SOMEBODY ETC THAT HAVE NEVER EVEN TRIED INDEXING. IN MY WORLD THATS CALLED BULL SHITTING. IF YOU...
GOT A REAL NICE SET OF UNMOLESTED HOLLEY FINNED ALUMINUM VALVE COVERS FOR SMALL BLOCK FORD ENGINES. 221-351 ENGINES PRICE $125.00 WILL...
GOT A REAL NICE SET OF EARLY UNMOLESTED EDELBROCK FINNED ALUM SCRIP VALVE COVERS FOR SBC. OLD POLISH JOB. HAD THEM SINCE LATE 60,S. CAN EMAIL...
TTT
GOT A COUPLE SETS OF CAMMEL HUMP SBC HEADS . BIG AND LITTLE HUMPS BOTH. $500.00 SET. I TOOK THESE OFF IN EARLY 70,S. 327/300 HP VETTE ENGINES....
ITS BEST TO USE HEAT WHEN PULLING THEM ALSO GRADE 8 FLAT WASHERS SACKED AND THE TALLEST GRADE 8 OR 9 NUTS, OIL THE THREADS TOO
A BUNCH OF NO ACTUAL EXPERIENCE OPINIONS...........THOSE ARE GREAT HEADS FOR UP TO 400HP, THEY NEED TO BE UPGRADED FOR UNLEADED GAS 1ST...
.125 dome with 76cc heads and felpro .040 head gasket will be 9.25 cr. perfect......also polish off all sharp edges on piston tops
HAS ANYBODY GOT ANY EXPERIENCE WITH A .030 OVER 350 CHEVY, .125 DOME HYPERUTECHTIC PISTONS, .015 STEEL SHIM HEAD GASKETS AND 76CC OPEN CHAMBER GM...
144,S ONLY HAVE 4 MAIN CAPS. VERY WEAK BOTTOM END. GO WITH A 250. SAME ENGINE FAMILY, TONS BETTER. ITS WHAT I,AM DOING IN MY 63 S22 COMET ALONG...
GOT A TOTAL OF 7 STAINLESS STEEL VALVES FOR 144-250 SMALL FORD 6 CYL. ENGINES FOR SALE. SWIRL POLISHED, NECKED DOWN STEMS, STOCK LENGTH, 1.84 HEAD...
Ashville north Carolina has a hill (mountain ) climb also. about 10 miles up curvy road. run anything
thanks but flair isn't what I want, soldier banjo fittings is what I want
somebodys gota know something.......................
good luck with Charlie price, talking about slow and chances of getting your carbs back that you send him is zero to none. been there done that....
I have 2 94,s he did and the work is superb and very reasonable
is there any other place to get the fittings / materials to make stainless/ soder joint fuel lines besides this Blundell fella ? he seems awful...
THE OLDER THE 300 THE BETTER THE ENGINE
got a real nice model A front crossmember, all original. glass bead blasted clean. call for more details. price is 350.00 + shipping from 37664...
SOLD THANKS HAMB BOARD BOB IN E.TN.
thank you so much !
WALTER, I,LL look into that. thank you so much pal. neet "real" hot rod also............ mind if i ask what size your tires are ? stands perfect !
to get it back on I was thinking to heat gear up in the oven to 450 degrees and pack shaft in dry ice for 3-4 hours. expand gear i.d. shrink shaft...
ok, got it a part with no problems, now to clean this mess up. its like axle grease inside just about. how do you press off the gear on the...
Separate names with a comma.
The Jalopy Journal
