New guy from E. Tx.

[steze48]

Hello, My name is Steve and am new to this forum.
I am in the process of putting together a 50 Dodge Wayfarer sedan.
I have installed a Ford 400 engine / C6 trans in it.
Had to move the firewall back about 4 inches to accomodate the engine.
Just received a 95 Explorer 8.8 rear end.
I have Scarebirds disc brake conversion on the front along with rack and pinion steering.

When I got the car I had to replace all the floor and rockers from scratch.
After everything that I have was fitted in place, welded or modified I tore it down for paint.
Bare frame has been panted with Eastwood's rust encapsulator.
I am in the process of cleaning up the underside of the body for more of the paint.
The rear body mount crossmember needs a little TLC...
I have some sheetmetal channel I found that will fit there with a little trimming.
I will post some pictures...
Let me know what you think...
Thank you, Steve

[1stGrumpy]

Hello Steve and welcome from Arkansas...

[duckman]

Welcome from another member in east Tx, I think I found a '50 dodge in a creek a few miles from my house , please post pic.s of your project
By the way are you near Henderson??? DUCKMAN

[pecker head]

Word from the can !

[firstnomad]

Welcome to the H.A.M.B. from Arkansas City, KS.

firstnomad

[stretch 1320]

Welcome from west Ga.

[wino01]

Welcome from New Waverly.

[apound]

welcome from another east texan

[badgeree]

And welcome from Melbourne, Australia.

[40fordtudor]

welcome from Rowlett--

[Sam Navarro]

Welcome from Texas City, TX

[wbrw32]

welcome...another east Texan

[hotskins]

Welcome from Virgina Beach

[Trucked Up]

Welcome from Kentucky.

Good luck on your project and keep us posted on your progress over on the main board.

[ARVCo.]

Steve, welcome aboard from Silver Spring, MD!

[todd_a]

Hey, welcome from Tyler!

[steze48]

Welcome from another member in east Tx, I think I found a '50 dodge in a creek a few miles from my house , please post pic.s of your project
By the way are you near Henderson??? DUCKMAN

Thank you Duckman...I'll take some more pictures shortly...Steve

[Okie Pete]

Welcome to the HAMB from Okla.

[steze48]

Thank you all for the welcome!!
I have cut the spring perches off the old axle today and will do the same on the 8.8
I will be using the original leaf springs which had that old anti-squeek wrap on them.
I have removed them and will clean and paint.
Still wire brushing the bottom of the car and have only the trunk pan left.
The spare tire well was rusted out so I cut the spot welds and removed it.
I will cut out a flat piece of 18ga. and fill the hole.
I will spend time tomorrow and take a group of pictures and post them.
In case you were wondering why I put a Ford 400 in, It was just overhauled and was free.
It and the C6 came out of a E-350 box van which is now a storage shead on wheels!?!
Steve

[steze48]

Welcome from another member in east Tx, I think I found a '50 dodge in a creek a few miles from my house , please post pic.s of your project
By the way are you near Henderson??? DUCKMAN

No Duckman....half way between Texarkana and Paris.
Steve

[wbrw32]

Hey Steze...You will get a lot more interest on you project by posting your photos over on the Main message board....This forum here is just for introductions,,Hope this helps..

[temper_mental]

Welcome from TX

[steze48]

Hey Steze...You will get a lot more interest on you project by posting your photos over on the Main message board....This forum here is just for introductions,,Hope this helps..


wbrw32, How do I find "The Main Message Board" !?!
I am new here and a little lost...Steve

[wbrw32]

wbrw32, How do I find "The Main Message Board" !?!
I am new here and a little lost...Steve
Just scroll down to the next forum..The Hokey Ass Message Board...Its right under the intro forum listing

[steze48]

I have started a build thread for my Wayfarer
http://www.jalopyjournal.com/forum/showthread.php?p=5427705#post5427705

[steze48]

Hello all...I have started a thread for my build at...
http://www.jalopyjournal.com/forum/showthread.php?p=5427705#post5427705
Please check it out.
Steve